Linear Satellite Radio MCT 11 User Manual

DESCRIPTION  
PROGRAM RECEIVER & TEST TRANSMITTER  
The MCT-11 MegaCode® digital transmitter is a wireless radio Refer to the instructions provided with the receiver to set it into  
control designed for use with automatic garage and gate “learnmode.With the receiver ready to learn, press the transmitter  
operators.  
button to program the transmitter into the receiver’s memory.  
MegaCode® transmitters and receivers do not contain a typical  
“coding switch”. Each transmitter is permanently coded at the  
factory. The transmitter sends a unique code when the button is  
pressed. The receiver is programmed by “learning” a transmitter’s  
unique digital code. The receiver will activate only from the  
“memorized” transmitters.  
MCT-11  
1-BUTTON  
DIGITAL  
TO PROGRAM THE CODE, WITH THE RECEIVER  
IN LEARN MODE, PRESS THE TRANSMITTER BUTTON  
TO SEND A SIGNAL TO THE RECEIVER  
TRANSMITTER  
The transmitter is powered by two Type 2032 “coin-cell” batteries.  
They should last 3 years with normal use.The red indicator on the  
face of the transmitter will glow when the unit is activated. If the  
indicator lights dimly, or not at all when transmitting, the batteries  
need to be replaced.To conserve battery life, an internal timer limits  
the transmission duration to 10 seconds if the transmitter button is  
held down.  
After programming, test the transmitter from various locations. Be  
sure the door or gate areas are clear. Activate the transmitter  
and verify that the receiver triggers the operator.  
Operation  
Instructions  
BE SURE THE DOOR OR  
GATE AREA IS CLEAR!  
ACTIVATE THE TRANSMTTER  
TO TEST THE RECEIVER  
AND OPERATOR  
(760) 438-7000  
USA & Canada (800) 421-1587 & (800) 392-0123  
Toll Free FAX (800) 468-1340  
VISOR CLIP INSTALLATION  
REPLACING THE BATTERIES  
LINEAR LIMITED WARRANTY  
This product is warranted to the consumer against defects in material and workmanship for one year from  
the date of purchase. This warranty applies to first retail buyers of new devices. Warrantor will repair, or at  
its option, replace, any device it finds that requires service under this warranty, and will return the repaired  
or replaced device to the consumer at the warrantor’s cost. For warranty service and shipping instructions  
contact warrantor at the address shown below. Devices must be sent to warrantor for service at owner’s  
expense. The remedies provided by this warranty are exclusive. Implied warranties under state law are to  
the one year period of this written warranty. Some states do not allow limitations on how long an implied  
warranty lasts, so the above limitation may not apply to you. In order to be protected by this warranty, save  
your proof of purchase and send copy with equipment should repair be required. This warranty gives you  
specific legal rights, and you may also have other rights which vary from state to state.  
TWIST DIME IN SLOT  
TO OPEN CASE  
1
2
LIFT OFF  
THE TOP OF  
THE CASE  
THE VISOR CLIP CAN  
BE INSTALLED FOR  
HORIZONTAL OR  
VERTICAL MOUNTING  
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact  
Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.  
NOTE: THE CIRCUIT BOARD WILL FIT ONLY ONE  
WAY INTO THE CASE. ALIGN THE PLASTIC POST  
IN THE CASE WITH THE HOLE IN THE CIRCUIT BOARD  
CAREFULLY  
REMOVE THE  
CIRCUIT BOARD  
3
IMPORTANT !!!  
Linear radio controls provide a reliable communications link and fill an important need in portable wireless  
signaling. However, there are some limitations which must be observed.  
SLIDE THE VISOR CLIP INTO ONE  
OF THE SLOTS ON THE REAR  
OF THE TRANSMITTER  
5
INSERT TWO NEW  
For U.S. installations only:The radios are required to comply with FCC Rules and Regulations as Part 15  
devices. As such, they have limited transmitter power and therefore limited range.  
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio  
signals that occur on or near their operating frequencies, regardless of code settings.  
Changes or modifications to the device may void FCC compliance.  
TYPE 2032 BATTERIES  
PLUS SIDE UP THEN  
REASSEMBLE UNIT  
Infrequently used radio links should be tested regularly to protect against undetected interference or  
fault.  
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor  
or dealer, and these facts should be communicated to the ultimate users.  
This device complies with FCC Part 15 and Industry Canada Rules and Regulations. Operation is subject  
to the following two conditions: (1) This device may not cause harmful interference, and (2) this device  
must accept any interference received, including interference that may cause undesired operation.  
4
REMOVE OLD BATTERIES  
AND DISPOSE OF THEM PROPERLY  
 
Copyright © 2005 Linear LLC  
225677 A  

Kuppersbusch USA Cooktop EKI 6072 User Manual
LG Electronics Blu ray Player BD640 User Manual
Life Fitness Bicycle LC 4000 User Manual
Lightolier Indoor Furnishings 1001FIC_3d User Manual
Lightolier Indoor Furnishings 1004F18ESR User Manual
Loewe Flat Panel Television 23332507020 User Manual
Martin Audio Portable Speaker W8LMI User Manual
M Audio Door IE 10 User Manual
Melissa Microwave Oven 753 133 User Manual
Microsoft Tablet Accessory t480 User Manual