Sylvania TV VCR Combo SRC21135 User Manual

OWNER’S  
MANUAL  
13-INCH COLOR TV/VCR  
SRC21135  
AUDIO  
VIDEO  
STOP/EJECT  
REW  
PLAY  
F.FWD  
REC/OTR  
CHANNEL  
VOLUME  
POWER  
This Owner’s Manual is made of  
recycled paper.  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
As an ENERGY STAR®  
Partner, our company has  
determined that this product meets  
the ENERGY STAR® guidelines for  
If you need additional assistance for set-up or operating  
after reading owner’s manual, please call  
TOLL FREE : 1-800-968-3429  
energy efficiency. ENERGY STAR® is  
a U.S. registered mark.  
 
Please read before using this equipment  
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
13.Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the TV/VCR, be sure the  
antenna or cable system is grounded so as to provide some  
protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code,  
ANSI/NFPA No. 70, provides information with respect to  
proper grounding of the mast and supporting structure,  
grounding of the lead-in wire to an antenna discharge unit,  
size of grounding conductors, location of antenna-discharge  
unit, connection to grounding electrodes, and requirements  
for the grounding electrode. (Fig. A)  
19.Damage Requiring Service-Unplug this TV/VCR from  
the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the  
TV/VCR.  
c. If the TV/VCR has been exposed to rain or water.  
d. If the TV/VCR does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions, as improper adjust-  
ment of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the TV/VCR to its normal operation.  
14.Lightning-For added protection for this TV/VCR receiver  
during a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall  
outlet and disconnect the antenna or cable system. This will  
prevent damage to the TV/VCR due to lightning and  
power-line surges.  
e. If the TV/VCR has been dropped or damaged in any way.  
f. When the TV/VCR exhibits a distinct change in perfor-  
mance-this indicates a need for service.  
15.Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
20.Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
21.Safety Check-Upon completion of any service or repairs to  
this TV/VCR, ask the service technician to perform routine  
safety checks to determine that the TV/VCR is in proper  
operating condition.  
16.Overloading-Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this TV/VCR through openings as they may touch dan-  
gerous voltage points or short out parts that could result in  
a fire or electric shock. Never spill liquid of any kind on  
the TV/VCR.  
22.Heat-This TV/VCR product should be situated away from  
heat sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce heat.  
18.Servicing-Do not attempt to service this TV/VCR yourself  
as opening or removing covers may expose you to danger-  
ous voltage or other hazards. Refer all servicing to quali-  
fied service personnel.  
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT.  
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE  
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.  
Download from Www.Somanuals-.c3om-. All Manuals Search And Download.  
EN  
9I03  
PRECAUTIONS  
IMPORTANT COPYRIGHT INFORMATION  
LOCATION  
For safe operation and satisfactory performance of  
your TV/VCR, keep the following in mind when  
selecting a place for its installation:  
Shield it from direct sunlight and keep it away  
from sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes  
at the top and bottom of the unit. Do not place the  
unit on a carpet because this will block the ventila-  
tion holes.  
Unauthorized recording or use of broadcast televi-  
sion programming, video tape, film or other copy-  
righted material may violate applicable copyright  
laws. We assume no responsibility for the unautho-  
rized duplication, use, or other acts which infringe  
upon the rights of copyright owners.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the TV/VCR near strong magnetic fields.  
Avoid moving TV/VCR to locations where temper-  
ature differences are extreme.  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If, by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to an  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the  
TV/VCR cassette holder.  
Do not place anything directly on top of the unit.  
WARNING  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place,  
or after heating a cold room or under conditions of  
high humidity. If a tape is played in a TV/VCR  
which has moisture, it may damage the tape and  
TV/VCR. Therefore if condensation occurs inside the  
unit, turn the POWER button on and allow at least 2  
hours for the unit to dry out.  
3) Connect the equipment to an outlet on a circuit  
different from that to which the receiver is con-  
nected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
Download from Www.Somanuals-.c4om-. All Manuals Search And Download.  
EN  
9I03  
TABLE OF CONTENTS  
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2  
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4  
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6  
C OPERATING CONTROLS AND FUNCTIONS 7  
C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20  
NORMAL RECORDING . . . . . . . . . . . . . . . . .20  
OTR (One Touch Recording) . . . . . . . . . . . . . .21  
TIMER RECORDING . . . . . . . . . . . . . . . . . . .21  
TIMER PROGRAM EXTENSION . . . . . . . . .22  
HINTS FOR AUTOMATIC TIMER  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23  
C PREPARATION FOR USE . . . . . . . . . . . . . . . .9  
ANTENNA/CABLE CONNECTIONS . . . . . . .9  
MOBILE CONNECTION . . . . . . . . . . . . . . . .10  
EXTERNAL INPUT MODE . . . . . . . . . . . . . .10  
INSTALLING THE BATTERIES . . . . . . . . . . .10  
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23  
WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24  
C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24  
C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25  
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . . .11  
CHANNEL SET UP FOR THE FIRST TIME . .11  
CLOCK SET UP (AUTO / MANUAL) . . . . . .11  
CHANNEL SET UP AGAIN . . . . . . . . . . . . . .13  
DELETING (OR ADDING) CHANNEL . . . . .13  
SELECTING THE LANGUAGE . . . . . . . . . . .13  
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .14  
C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25  
REAL TIME TAPE COUNTER . . . . . . . . . . . .25  
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25  
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25  
C TROUBLESHOOTING GUIDE . . . . . . . . . . .26  
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27  
C CABLE CHANNEL DESIGNATIONS . . . . . .27  
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover  
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14  
WATCHING A TV PROGRAM . . . . . . . . . . . .14  
GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14  
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15  
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15  
CLOSED CAPTION SYSTEM . . . . . . . . . . . .15  
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .16  
C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17  
AUTO REPEAT PLAYBACK . . . . . . . . . . . . .18  
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . .19  
RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .19  
VERTICAL HOLD CONTROL . . . . . . . . . . . .20  
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .20  
TRACKING ADJUSTMENT . . . . . . . . . . . . . .20  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-  
tions concerning chemical wastes.  
Download from Www.Somanuals-.c5om-. All Manuals Search And Download.  
EN  
9I03  
FEATURES  
Rotary 4-head Record/Playback System–Four  
heads ensure excellent picture quality and special  
effects playback.  
Index Search–Fast-forwards to start of next recording.  
Slow Motion–View recorded program at slower  
than normal speed.  
Infrared remote control  
Bilingual on screen menu display selectable in  
English or Spanish  
Auto Head Cleaner–Automatically cleans video  
heads as you insert or remove a cassette.  
Zero Return–The tape returns to counter of  
0:00:00 by rewinding or fast forwarding.  
Still–“Freeze” the picture at any time, for close  
viewing of a particular scene. Only tapes recorded  
in SLP mode will show a fairly clear picture.  
Digital Auto Tracking (DTR)–Automatically  
adjusts the tracking for each tape you play.  
Rental play mode–Improves playback picture  
quality from worn tapes, such as rental tapes.  
Auto repeat–Allows you to repeat the playing of a  
tape indefinitely without pressing the PLAY button.  
Time search–Lets you set the TV/VCR to advance  
the tape by entering the desired playback time you  
want to skip.  
Real time counter–This shows the elapsed record-  
ing or playback time in hours, minutes, and sec-  
onds. The “–” indication will appear when the tape  
is rewound further than the tape counter position  
“0:00:00”.  
181 channel capability PLL frequency synthesiz-  
er tuner with direct station call–(A converter may  
be necessary to view scrambled cable channels.)  
Auto Clock Setting–Allows you to set the clock  
from a PBS broadcast station.  
Closed caption system–You may view specially  
labeled (cc) TV programs, movies, news, prere-  
corded tapes, etc. with either a dialogue caption or  
text display added to the program.  
Game mode–Automatically sets external input  
mode and allows the TV/VCR display to be suit-  
able for use with TV games.  
Auto power on and off system–Automatically  
turns on the TV/VCR when you insert the cassette,  
turns off after auto-rewind, and ejects when the  
beginning of the tape is reached.  
Auto rewind when the end of a tape is  
reached–This function doesn’t occur when using  
timer recording.  
2 Step picture search operation–You can view a  
video program at a high speed or super high speed  
in either a forward or reverse direction in LP and  
SLP mode. For SP mode only high speed.  
Three different playback tape speeds : SP/LP/SLP  
Two different recording tape speeds : SP/SLP  
OTR (One Touch Recording)–Instant timed  
recording from 30 to 480 minutes is possible at the  
push of the REC/OTR button.  
1 Year, 8 events (including Daily and Weekly  
Timer Recording)–The built-in timer allows you to  
record up to 8 programs at different times on dif-  
ferent channels up to 1 year in advance. The Daily  
timer allows recordings to be made of daily broad-  
casts, and the Weekly timer allows recording to be  
made once a week up to the end of the tape.  
Auto return–After timer recording is finished, the  
TV/VCR can return to the beginning of the record-  
ing.  
Wake-up/Sleep timer–Allows you to have the  
TV/VCR automatically turn on or off at a desired  
time.  
Timer Program Extension–Allow you to shift the  
time schedule for automatic timer recording.  
V-CHIP–Enables parents to prevent their children  
from watching inappropriate material on TV.  
Two- way powerAllows you to power the  
TV/VCR with standard household AC or your vehi-  
cle’s battery, using the supplied car-battery cord.  
SUPPLIED ACCESSORIES  
AC Cord  
2 AA  
Batteries  
Remote Control Unit  
Rod Antenna  
Car Battery Cord  
PART NO  
(N0145UD or  
N0157UD)  
(0EMN00673 or  
0EMN01599 or  
0EMN01755)  
(WPV0182LW001 or  
WPV0182HHH01)  
(WPC0192HD002)  
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-  
968-3429.  
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators  
(Splitter). Contact your local electronics store for these items.  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control. If you decide to use a universal remote control with this unit, please be aware  
that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-  
versal remote control.  
Download from Www.Somanuals-.c6om-. All Manuals Search And Download.  
EN  
9I03  
OPERATING CONTROLS AND FUNCTIONS  
- TV/VCR FRONT PANEL -  
AUDIO  
VIDEO  
STOP/EJECT  
REW  
PLAY F.FWD  
REC/OTR  
CHANNEL  
VOLUME  
POWER  
1
2
3
4
5
6
7
8 9 10  
11  
12 13  
14  
- REMOTE CONTROL -  
L button–  
Press to select setting modes from the on screen  
menu.  
Press to enter digits when setting program.  
(for example: setting clock or timer program)  
25  
4
WAKE-UP  
/SLEEP  
POWER  
EJECT  
13  
15  
CHANNEL  
RETURN  
4 EJECT button [Remote control]– Press in the  
Stop mode to remove tape from TV/VCR.  
5 REW button– Press to rewind the tape, or to view  
the picture rapidly in reverse during playback  
mode. (Rewind Search)  
1
4
7
2
5
8
3
6
9
24  
CHANNEL  
VOLUME  
11  
12  
0
+100  
MENU  
s button–  
DISPLAY  
MUTE  
16  
17  
5
Press to select a mode from a particular menu.  
23  
6
(for example: LANGUAGE or USER’S SET UP)  
6 PLAY button– Press to begin playback.  
K button–  
PLAY  
7
REW  
F.FWD  
STOP  
4
RECORD  
SPEED PAUSE/STILL  
22  
21  
Press to select setting modes from the on  
screen menu.  
Press to enter digits when setting program.  
8
18  
T-PROG.  
CLEAR  
GAME  
SLOW  
COUNTER  
RESET  
19  
20  
(for example: setting clock or timer program)  
7 F.FWD button– Press to rapidly advance the tape,  
or to view the picture rapidly in forward during  
playback mode. (Forward Search)  
B button–  
1 EARPHONE jack– Connects to earphones (not  
supplied) for personal listening. The size of jack is  
1/8” monaural (3.5mm).  
2 AUDIO input jack– Connect to the audio output  
jack of your audio equipment, video camera or  
another VCR.  
When setting program (for example: setting clock  
or timer program), press to determine your selec-  
tion and proceed to the next step you want to input.  
Press to determine setting modes from on screen  
menu.  
3 VIDEO input jack– Connect to the video output  
jack of your video camera or another VCR.  
4 STOP button [TV/VCR ]– Press to stop the tape  
motion.  
Press to select a mode from a particular menu.  
(for example: LANGUAGE or USER’S SET UP)  
EJECT button [TV/VCR ]– Press in the Stop mode  
to remove tape from TV/VCR.  
Download from Www.Somanuals-.c7om-. All Manuals Search And Download.  
EN  
9I03  
- REAR VIEW -*  
DC 13.2V  
AC 120V  
ANT.  
26  
27 28  
8 REC button– Press for manual recording.  
OTR button– Activates One Touch Recording.  
(only on the TV/VCR)  
9 RECORD indicator– Flashes during recording.  
Lights up in the Stand-by mode for Timer Recording.  
10 Remote Sensor Window– Receives the infrared  
signals from the remote control.  
11 CHANNEL K / L buttons– Press to select the  
desired channels for viewing or recording, listening  
of FM radio.  
18 SPEED button– Press to choose the desired  
recording speed:SP/SLP.  
19 T-PROG. CLEAR button– Press to cancel a setting  
of timer program. (See page 23.)  
COUNTER RESET button– Press to reset counter  
to 0:00:00.  
20 GAME button– Sets the game mode and external  
input mode at the same time. (See page 14.)  
21 SLOW button– Press to start slow motion playback.  
The slow speed can be controlled by pressing the  
F.FWD button (faster) or the REW button (slower).  
(only on the remote control).  
22 PAUSE/STILL button– Press to temporarily stop  
the tape during the recording or to view a still pic-  
ture during playback.  
You may display the main menu on the TV screen  
by pressing repeatedly this button on the TV/VCR.  
TRACKING function– Press to minimize video  
‘noise’ (lines or dots on screen) during playback  
or Slow mode. (See page 20.)  
Frame Advance function– Press to advance the  
picture one frame at a time during Still mode.  
23 MUTE button– Mutes the sound. Press it again to  
resume sound.  
12 VOLUME X / Y buttons– Adjust the volume level.  
13 POWER button– Press to turn TV/VCR on and  
off. Press to activate timer recording.  
14 Cassette compartment  
24 CHANNEL RETURN button– Press to go back to  
the previously viewed channel. For example,  
pressing this button once will change channel dis-  
play from 3 (present channel) to 10 (previously  
viewed channel), and pressing it a second time  
will return from 10 to 3.  
25 WAKE UP/SLEEP button– Sets the Wake up or  
Sleep Timer. (See page 23 and 24.)  
26 ANT. terminal– Connect to an antenna or cable  
system.  
15 Number buttons– Press to select desired channels  
for viewing or recording. To select channels from  
1 to 9, first press the 0 button and then 1 to 9.  
+100 button– When selecting cable channels which  
are higher than 99, press this button first, then press  
the last two digits. (To select channel 125, first press  
the “+100” button then press “2” and “5”).  
16 MENU button– Press to display the main menu on  
the TV screen.  
17 DISPLAY button– Display the counter or the cur-  
rent channel number and current time on the TV  
screen. (See page 25.)  
27 DC 13.2V jack– Connect to the Car Battery Cord.  
28 AC 120V jack– Connect to the AC cord.  
Download from Www.Somanuals-.c8om-. All Manuals Search And Download.  
EN  
9I03  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTIONS  
From Cable System or  
Satellite Dish  
VHF/UHF Antenna  
(Not supplied)  
Rod Antenna  
(Supplied)  
Satellite Box or  
Cable Box  
OUT  
IN  
(Not supplied)  
VHF Antenna  
(Not supplied)  
UHF Antenna  
(Not supplied)  
From  
Cable System  
or  
DC 13.2V  
AC 120V  
ANT.  
VHF/UHF  
Combiner  
(Not supplied)  
or  
ANT.  
or  
75-ohm Coaxial  
Cable (Not supplied)  
Flat twin-lead cable  
or  
VHF/UHF COMBINED ANTENNA  
VHF/UHF SEPARATE ANTENNAS  
The VHF/UHF Rod Antenna (supplied) is detach-  
able. Insert the stem of the antenna into the hole on  
the upper-back portion of the TV/VCR.Connect the  
VHF/UHF Rod Antenna or VHF/UHF Combination  
Antenna to the ANT. terminal of the TV/VCR as  
shown in the diagram. For the best reception, fully  
extend the VHF/UHF Rod Antenna and make the  
necessary adjustments. (Avoid touching the top sec-  
tion when adjusting.)  
In some areas it will be necessary to use an outdoor  
antenna.  
CABLE WITHOUT CONVERTER/  
DESCRAMBLER BOX  
Use this connection if your cable system connects  
directly to your TV/VCR without a converter box.  
By using this connection you can:  
1) Use the TV/VCR remote to select channels.  
2) Program one or more unscrambled channels for  
Automatic Timer Recording.  
NOTE: This unit will ONLY record and view the  
same channel.  
NOTE:  
Before plugging the Rod antenna into antenna termi-  
nal, check that the pin is not bent. If it is bent,  
straighten the pin as illustrated, then plug the pin into  
antenna terminal.  
CABLE WITH CONVERTER/  
DESCRAMBLER BOX OR SATELLITE  
BOX  
Bent pin  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown in the diagram.  
Cable Plug  
(Straight pin)  
(Needs to be straightened)  
By using this connection you can also record scram-  
bled channels. However, channel selection must be  
made with the converter box or satellite box. This  
means that channels cannot be changed using the  
TV/VCR Remote Control. Unattended timer record-  
ing is limited to one channel at a time.  
NOTE:  
The connection of an indoor antenna may not always  
give acceptable TV reception.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-  
ed to the grounding system of the building as close to the point of cable entry as practical.  
Download from Www.Somanuals-.c9om-. All Manuals Search And Download.  
EN  
9I03  
TO RECORD A SCRAMBLED/UNSCRAMBLED  
CHANNEL  
EXTERNAL INPUT MODE  
1) Set the TV/VCR channel selector to the output  
channel of the Cable Converter Box or Satellite  
Box. (Example: CH3)  
When using an external input signal (another VCR or  
video camera), connect the player’s audio/video out-  
put cables to the AUDIO IN/ VIDEO IN jacks of  
2) Select the channel to record from your Cable  
Converter Box or Satellite Box.  
AUX  
MOBILE CONNECTION  
WARNING:The driver should never watch  
the TV/VCR while operating a motor vehicle.  
INSTALLING THE BATTERIES  
CAUTION: If you use the TV/VCR with the  
vehicle’s engine off, recharge the vehicle’s  
battery after every 4 hours of use to prevent  
it from running down. After you finish using  
the TV/VCR be sure you unplug the car-bat-  
tery cord from the cigarette-lighter socket.  
1)Open the battery compartment cover by pressing  
the cover on the remote unit in the direction of the  
arrow.  
2)Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
1) The supplied indoor antenna is adequate when  
your vehicle is stationary. For best reception on  
the road, use a high-quality VHF/UHF mobile TV  
antenna.  
3)Replace the cover.  
2) Attach the car battery cord to the DC13.2V (12V)  
connector on the back of the TV/VCR. Then, con-  
nect the other end to your vehicle’s cigarette-  
lighter socket.  
NOTES:  
Be sure your vehicle has a 13.2-volt (12-volt), neg-  
ative-ground electrical system.  
Be sure you use only the supplied car battery cord.  
Using another cord could damage the TV/VCR.  
Be sure the socket is free of ashes and other debris.  
Be sure to push the car battery cord’s plug com-  
pletely into the cigarette-lighter socket.  
Always unplug the car battery from the cigarette-  
lighter socket before you unplug it from the  
TV/VCR.  
You must disconnect the car battery cord from the  
TV/VCR before you can use the AC power.  
Be sure to replace the fuse with only the same  
type, 5A, 250V.  
To the vehicle's  
cigarette-lighter socket  
VHF/UHF Combination  
Mobile Antenna  
(Not supplied)  
Car battery cord  
(Supplied)  
DC 13.2V  
AC 120V  
DC13.2V  
ANT.  
ANT.  
- 10 -  
EN  
9I03  
 
SET UP FOR USE  
You can program the tuner to scan all the channels  
TO SELECT A DESIRED CHANNEL  
You can select the desired channel by using the  
CHANNEL K or L button or directly pressing the  
number buttons on the remote control.  
you receive in your area.  
NOTE: Channel memory programming is NOT  
needed when connected to a cable box or satellite  
box. Just select the TV/VCR channel selector to the  
output channel of the cable box or satellite box (Ex  
CH3). Then select the channel to be viewed on the  
Cable Box or Satellite Box.  
Note for using the number buttons:  
When selecting cable channels which are higher  
than 99, press the +100 button first, then, press the  
last two digts. (Example: to select channel 125,  
first press the +100 button then press “2” and “5”).  
CHANNEL SET UP FOR THE  
FIRST TIME  
You must proceed single-digit channel numbers  
with a zero (Example: 02 ... 09).  
1 Plug in the TV/VCR  
power cord  
(Rear)  
Plug the TV/VCR power  
AC 120V  
CLOCK SET UP  
(AUTO / MANUAL)  
Set the clock accurately for proper automatic timer  
recording. If the Public Broadcasting Station (PBS)  
is available in your area, follow “AUTO CLOCK  
SETTING”. If it is not, follow “MANUAL CLOCK  
SETTING”.  
cord into a standard AC  
outlet.  
NOTE:  
If some digits appear  
in the corner of the screen, press the POWER but-  
ton without unplugging the power cord.  
2 Turn on the TV/VCR  
AUTO CLOCK SETTING  
Press the POWER button to turn on the TV/VCR  
You can have the TV/VCR set the clock automatical-  
ly by using the Public Broadcasting Station (PBS)  
channel in your area. Once you have set the clock by  
using the following procedure, the TV/VCR will  
automatically monitor the correct time and date  
being broadcast by the PBS station in your area,  
using a new service called Extended Data Service  
(XDS).  
3 Select “ENGLISH” or “ESPAÑOL”  
SET UP –  
Select “ENGLISH” or  
B
LANGUAGE  
“ESPAÑOL”=Spanish using the  
F.FWD/B or REW/s button. “[ ]”  
indicate the selected language.  
[ENGLISH] ESPAÑOL  
AUTO PRESET  
Make sure ...  
TV/VCR power must be turned on.  
Confirm that the antenna connections are correct.  
The cable converter box must be turned on if your  
TV/VCR is connected directly to it. (See NOTES:)  
4 Begin auto preset  
SET UP –  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO PRESET”.  
Then press the F.FWD/B button.  
The tuner scans and memorizes all  
active channels in your area.  
LANGUAGE  
[ENGLISH] ESPAÑOL  
B
AUTO PRESET  
The channel is properly set in advance.  
NOTES:  
NOTES:  
The TV/VCR distinguishes between standard TV  
channels and cable channels.  
Auto clock setting only needs to be set once. But it  
can be done again if the clock’s time has become  
incorrect for some reason.  
If you want to play or record a video tape  
BEFORE presetting the tuner, you must press the  
MENU button on the remote control. To preset the  
tuner again, see “CHANNEL SET UP AGAIN” on  
page 12.  
If the TV/VCR is connected directly to a cable  
converter box or satellite box, the local PBS station  
must be selected on the cable box itself, and the  
TV/VCR must be set to the output channel of the  
cable converter box or satellite box (usually chan-  
nel 3 or 4), to be able to set up or correct the clock  
automatically.  
The TV/VCR may memorize TV channels as  
CATV channels if reception conditions are poor. If  
this happens, try the AUTO MEMO action again  
when reception conditions are better.  
If you do not know what your local PBS station is,  
then follow “Manual Clock Settings”.  
5 After scanning  
The TV/VCR cannot control the channels of the  
cable converter box or satellite box.  
If tou use a mobile connection, you cannot set the  
AUTO CLOCK and D.S.T functions.  
The tuner stops on the lowest memorized channel.  
If you want to recall the selected channels, you can  
select the desired channel directly with the remote  
control number buttons or CHANNEL K or Lbutton.  
- 11 -  
EN  
8H30  
 
M E N U –  
M E N U –  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “SETTING  
CLOCK”.  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control. Press the PLAY/K  
or STOP/L button to point to “SET-  
TING CLOCK”.  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USERS SET UP  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USERS SET UP  
B
B
V-CHIP SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
ZERO RETURN  
TIME SEARCH  
TIME SEARCH  
INDEX SEARCH  
INDEX SEARCH  
Then, press the F.FWD/B button.  
Then, press the F.FWD/B button.  
SETTING CLOCK –  
2 Select “MANUAL CLOCK  
SETTING CLOCK –  
AUTO CLOCK  
[ON]  
2 Set “AUTO CLOCK” to [ON]  
Press the F.FWD/B or REW/s  
button repeatedly until [ON]  
appears.  
SET”  
AUTO CLOCK CH  
[AUTO]  
[OFF]  
B
AUTO CLOCK  
[ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “MANUAL CLOCK  
SET”.  
AUTO CLOCK CH  
[AUTO]  
[OFF]  
B
MANUAL CLOCK SET  
D.S.T.  
MANUAL CLOCK SET  
D.S.T.  
Then, press the F.FWD/B button.  
3 Enter the channel number for  
the PBS station  
SETTING CLOCK –  
MANUAL CLOCK SET –  
MONTH DAY YEAR  
3 Select the month  
AUTO CLOCK  
[ON]  
B
AUTO CLOCK CH  
[AUTO]  
Press the PLAY/K or STOP/L but-  
ton until your desired month  
appears. (Example: May 05)  
Then, press the F.FWD/B button.  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO CLOCK  
CH”.  
Then press the F.FWD/B or REW/s button until the  
channel number for your local PBS station appears.  
If you do not know the PBS channel number, leave it  
set to [AUTO] which is located before [2]. The  
TV/VCR will search automatically all available chan-  
nels for the local PBS station, and will select that  
channel.  
0 5  
/
– – – – – – – – –  
MANUAL CLOCK SET  
D.S.T.  
HOUR  
MINUTE  
[OFF]  
– –  
:
– – – –  
MANUAL CLOCK SET –  
MONTH DAY YEAR  
4 Select the day  
Press the PLAY/K or STOP/L but-  
ton until your desired day appears.  
(Example: 1st 01)  
0 5  
/
0 1 – – – – – – –  
HOUR  
MINUTE  
– –  
:
– – – –  
Then, press the F.FWD/B button.  
4 Exit the Auto Clock Setting  
Press the MENU button on the remote control to  
return to TV mode.  
MANUAL CLOCK SET –  
MONTH DAY YEAR  
5 Select the year  
Press the PLAY/K or STOP/L but-  
ton until your desired year appears.  
(Example: 2001)  
0 5  
/
0 1 TUE 2 0 0 1  
HOUR  
MINUTE  
– –  
:
– – – –  
Then, press the F.FWD/B button.  
5 Turn off the TV/VCR  
Turn the TV/VCR off. The Auto Clock functions  
automatically while the TV/VCR is off.  
MANUAL CLOCK SET –  
MONTH DAY YEAR  
6 Select the hour  
Press the PLAY/K or STOP/L but-  
ton until your desired hour appears.  
(Example: 5, PM)  
If you choose [AUTO],  
0 5  
/
0 1 TUE 2 0 0 1  
The TV/VCR must search until the PBS channel is  
HOUR  
0 5  
MINUTE  
:
– – PM  
found. It must scan each channel for a couple of  
seconds to determine if that channel is transmitting  
the XDS signal.  
Then, press the F.FWD/B button.  
MANUAL CLOCK SET –  
MONTH DAY YEAR  
7 Select the minute  
If the time that is automatically set by this selected  
Press the PLAY/K or STOP/L but-  
ton until the desired minute appears.  
(Example: 40)  
PBS station is incorrect, it may not be your local  
PBS station, but one from a different time zone.  
Or if no channel is broadcasting the XDS signal in  
your area, no time will show. In these cases, you  
must manually enter the correct local PBS station,  
or set the clock manually and turn off the Auto  
Clock Setting feature.  
0 5  
/
0 1 TUE 2 0 0 1  
HOUR  
0 5  
MINUTE  
4 0 PM  
:
5:40 PM  
8 Start the clock  
Press the MENU button on the  
remote control.  
MANUAL CLOCK SETTING  
Although seconds are not displayed,  
they begin counting from 00 when  
you press the MENU button on the remote control.  
Use this feature to synchronize the clock with the  
correct time.  
Make sure ...  
TV/VCR power must be turned on.  
In the example below, the clock is to be set to:  
DATE  
May 1st, 2001  
SETTING TIME 5:40PM  
- 12 -  
EN  
8H30  
 
NOTE:  
When unplugging the AC cord or if there is a power  
failure for more than 30 seconds, you may have to  
reset the clock.  
1 Select “CHANNEL SET UP”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USERS SET UP  
B
TO CHANGE CLOCK SETTING  
If you want to change the clock,  
1)Follow steps [1] and [2].  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
Then, press the F.FWD/B button.  
2)Select where you want to change using the  
F.FWD/B or REW/s button.  
3)Enter correct numbers using the PLAY/K or  
STOP/L button.  
4)Press the MENU button on the remote control to  
start the clock.  
CHANNEL SET UP –  
2 Select “ADD/DELETE CH”  
Press the PLAY/K or STOP/L but-  
ton to point to “ADD/DELETE  
CH”.  
B
ADD / DELETE CH (TV)  
AUTO PRESET  
Press the F.FWD/B button.  
PLEASE NOTE:  
If there is no local PBS station in your area or on  
your cable system, select “AUTO CLOCK” and press Press the PLAY/K or STOP/L but-  
3 Enter the desired channel number  
the F.FWD/B or REW/s button to turn [OFF] this  
function. Then you can manually adjust the clock.  
ton until your desired channel num-  
ber appears. (You can also use the  
number buttons or the CHANNEL  
K/L button to enter it.) (Example:  
CH8)  
08  
ADD / DELETE  
CHANNEL SET UP AGAIN  
Make sure ...  
4 Delete (or add) it from (into) memory  
Press the POWER button to turn on the TV/VCR.  
Press the F.FWD/B or REW/s button. The channel  
number changes to light red. The channel is deleted  
from memory.  
1 Select “CHANNEL SET UP”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
To delete another channel, repeat steps [3] and [4].  
If you press the F.FWD/B or REW/s button  
again, the channel is memorized again.  
SETTING CLOCK  
B
CHANNEL SET UP  
USERS SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
Added channel: Light blue.  
Deleted channel: Light red.  
Then, press the F.FWD/B button.  
2 Begin auto preset  
CHANNEL SET UP –  
5 Exit the channel setup mode  
ADD / DELETE CH (TV)  
AUTO PRESET  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO PRESET”.  
Then, press the F.FWD/B button.  
The tuner scans and memorizes all  
the active channels in your area.  
Press the MENU button on the remote control to  
returns to TV mode.  
B
NOTE: To confirm that channel(s) has been deleted  
or added, press the CHANNEL K or L button.  
SELECTING THE LANGUAGE  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
NOTE: This function effects only the language on  
3 After scanning  
The tuner stops on the lowest memorized channel.  
the screen menu and not the audio source.  
DELETING (OR ADDING)  
CHANNEL  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you  
can add the deleted channel into the memory again.)  
M E N U –  
1 Select “LANGUAGE”  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “LANGUAGE”.  
CHANNEL SET UP  
USERS SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
B
- 13 -  
EN  
8H30  
 
M E N U –  
2 Select “ENGLISH” or “ESPAÑOL”  
Select “ENGLISH” or “ESPAÑOL”= Spanish using  
the F.FWD/B or REW/s button.  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L  
button to point to “SETTING  
CLOCK”.  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USERS SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
3 Exit the Language mode  
Press the MENU button on the remote control to  
return to TV mode.  
Then, press the F.FWD/B button.  
NOTE: If for some reason the menu is in Spanish,  
press the MENU button on the remote control, press  
the PLAY/K button to point to “IDIOMA  
[ESPAÑOL]”, then press the F.FWD/B button, then  
press the MENU button on the remote control.  
2 Set “D.S.T.(Daylight-Saving Time) to [ON]  
Press the PLAY/K or STOP/L  
SETTING CLOCK –  
button to point to “D.S.T.”.  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH  
[AUTO]  
Then, press the F.FWD/B or  
REW/s button until [ON]  
appears.  
MANUAL CLOCK SET  
D.S.T.  
B
[ON]  
DAYLIGHT-SAVING TIME  
Select this feature and the TV/VCR’s clock automati-  
cally will advance one hour in April, then reverse one  
hour in October.  
When Daylight-Saving Time is ON, the clock will  
change automatically as follows:  
3 Exit the Daylight-Saving Time mode  
Press the MENU button on the remote control to  
return to TV mode.  
NOTE: If tou use a mobile connection, you cannot  
set the AUTO CLOCK and D.S.T functions.  
First Sunday of April : At 2 AM the clock imme-  
diately changes to 3 AM. Any timer programming  
you have set to occur between 2 AM and 3 AM  
will not record.  
Last Sunday of October : At 2 AM the clock  
immediately changes to 1 AM.  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
TO CANCEL THE DAYLIGHT-SAVING  
TIME  
Repeat steps [1] to [2], select [OFF] using the  
F.FWD/B or REW/s button.Then, press the  
MENU button on the remote control to return to  
TV mode.  
TV OPERATION  
WATCHING A TV PROGRAM  
GAME MODE  
This function enables you to decrease the TV screen  
contrast and making it suitable for use with a TV  
GAME.  
1 Turn on the TV/VCR  
Press the POWER button to turn on the TV/VCR.  
NOTE: This function can not be set during recording.  
2 Select the channel number  
Press the CHANNEL K or L button to select your  
desired channel number or press the number buttons  
on the remote control.  
Press the GAME button on the  
remote control. “GAME” appears  
on the screen.  
GAME  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be viewed must be selected  
on the cable box or satellite box.  
When you press the GAME button;  
The TV/VCR comes on automatically if it is off.  
The TV/VCR will be in external input mode auto-  
matically.  
3 Adjust sound  
Press the VOLUME X or Y button  
to adjust the volume.  
TO CANCEL THE GAME MODE  
Press the GAME button or CHANNEL K or L but-  
ton on the remote control.  
VOLUME 20  
C
C
C
C
C
C
C
C
C
C
C
C
- 14 -  
EN  
8H30  
 
DEGAUSSING  
Magnetism from nearby appliances might affect the  
color of the TV picture.  
If this happens, move this unit away from the appli-  
ance. If the color is still not correct, disconnect  
power cord from AC outlet then reconnect it after 30  
minutes.  
CLOSED CAPTION SYSTEM  
You can view specially labeled (cc) TV programs,  
movies, news, pre-recorded tapes with either a dia-  
logue caption or text display.  
CAPTION mode: By choosing the caption mode, you  
can watch dramas, movies and news while captioning  
the dialogues and the contents of news.  
TEXT mode: By choosing the text mode, you can  
watch half screen text information if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. Caption “2” is usually  
used for a second language if available.  
PICTURE CONTROL  
The TV/VCR’s picture controls – BRIGHT, CON-  
TRAST, COLOR, TINT and SHARPNESS – are  
preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a natural looking image.  
NOTES:  
Procedures must be followed within 5 seconds or  
the Picture Control mode will be cancelled.  
When setting the Picture Control, the Game mode  
will be cancelled.  
NOTE:  
Not all programs are broadcast with closed captions.  
Your television is designed to provide error free  
closed captions from high quality antenna, cable and  
VCR signals. Conversely, poor quality signals are  
likely to result in caption errors or no captions at all.  
Common signal conditions which may cause captions  
errors are listed below:  
Make sure ...  
TV/VCR power must be turned on.  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture  
1 Select “PICTURE CONTROL”  
M E N U –  
TIMER PROGRAMMING  
Press the MENU button on the  
B
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USERS SET UP  
V-CHIP SET UP  
remote control.  
ghosts or airplane flutter.  
Press the PLAY/K or STOP/L but-  
ton to point to ”PICTURE CON-  
TROL”.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Playback of poorly recorded or worn VCR tapes.  
NOTE:  
TIME SEARCH  
INDEX SEARCH  
If the TV/VCR displays a black box on the TV  
screen, this means that the TV/VCR  
is set to the TEXT mode. To clear  
screen, select [CAPTION1], [CAP-  
TION2] or [OFF].  
Then, press the F.FWD/B button.  
2 Select item you want to adjust  
Press the PLAY/K or STOP/L but-  
ton until desired control is dis-  
played.  
Make sure ...  
TV/VCR power must be turned on.  
BRIGHT / CONTRAST /  
COLOR / TINT /  
SHARPNESS  
BRIGHT  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
M E N U –  
1 Select “CAPTION”  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USERS SET UP  
Press the MENU button on the  
remote control.  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
3 Adjust the picture control  
Press the F.FWD/B or REW/s button to adjust to  
your desired level.  
B
Press the PLAY/K or STOP/L but-  
ton to point to “CAPTION”.  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
REW/s  
to decrease  
brightness  
to decrease  
contrast  
F.FWD/B  
to increase  
brightness  
to increase  
contrast  
2 Select your desired caption menu  
M E N U –  
BRIGHT  
Press the F.FWD/B or REW/s  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USERS SET UP  
button until your desired caption  
menu appears.  
([CAPTION1], [CAPTION2],  
[TEXT1] or [TEXT2])  
CONTRAST  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [CAPTION1]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
B
COLOR  
TINT  
to pale  
to brilliant  
to purple  
SHARPNESS to soft  
to green  
to clear  
3 Exit the caption setting mode  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
- 15 -  
EN  
8H30  
 
TO CANCEL THE CLOSED CAPTION  
SYSTEM  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button. Press the MENU but-  
ton on the remote control to return to TV mode.  
3 Select your desired item  
Press the PLAY/K or STOP/L but-  
ton to point to your desired item.  
Then, press the F.FWD/B button to  
select [BLOCK] or [VIEW].  
B
TVY  
TVY7  
TVG  
TVPG (  
TV14  
TVMA(  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
(
)
)
)
)
(
When you select the rating category and turn it  
WHEN THE CLOSED CAPTION MODE  
IS ON  
The On-Screen Display will disappear after 5 sec-  
onds.  
[BLOCK], the higher rating will turn [BLOCK]  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
When you turn “TV-Y” to [VIEW], then all ratings  
will turn to [VIEW] automatically.  
This is also true when the MUTE button is pressed,  
and when the PAUSE/STILL button is pressed  
while recording.  
Selection  
TV-Y  
Rating Category Explanations  
Appropriate for all children  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
TV-Y7  
TV-G  
Appropriate for children seven and older  
General Audience  
TV-PG  
TV-14  
Parental Guidance suggested.  
Unsuitable for children under 14  
V-CHIP SET UP  
TV-MA Mature audience only  
V-CHIP enables parents to prevent their children  
from watching inappropriate material on TV.  
V-CHIP reads the ratings for programming (except  
for news and sports programs, unedited movies on  
premium cable channels, and Emergency Broadcast  
System signals), then denies access to programming  
if the program’s rating meets the limitations you  
select. In this case, “PROTECTED PROGRAM by  
...” message appears on the TV screen.  
When you select TV-Y7, TV-PG, TV-14, or TV-MA  
and you press the F.FWD/B button, the sub-ratings  
will appear on the TV screen.  
If you select the rating category (example: TV-PG)  
and turn it [BLOCK] or [VIEW], the sub-ratings  
(example: V for Violence) will turn [BLOCK] or  
[VIEW] automatically.  
You can set the sub-ratings to [BLOCK] or [VIEW]  
individually when the rating category is set to  
[BLOCK].  
To set the sub-ratings individually, follow the steps  
below.  
To block certain ratings, follow the steps below.  
Programming may be rated by the Motion Picture  
Association of America (MPAA) or according to  
the Television Parental Guidelines. In order to  
block any inappropriate programming, set your  
limits in both places (MPAA RATING and TV  
RATING).  
When you select [TV-Y7]:  
Press the STOP/L or PLAY/K  
button to select “FV” (Fantasy  
Violence).  
TVY7  
[BLOCK]  
[BLOCK]  
B
FV  
Then, press the F.FWD/B button  
to select [BLOCK] or [VIEW].  
When you select [TV-PG], [TV-  
14] or [TV-MA]:  
Press the STOP/L or PLAY/K button to select  
TV RATING SET UP  
Make sure ...  
TV/VCR power must be turned on.  
“D”(Suggestive Dialog),  
“L”(Coarse Language),  
1 Select “V-CHIP SET UP”  
M E N U –  
TIMER PROGRAMMING  
TVPG  
[BLOCK]  
PICTURE CONTROL  
Press the MENU button on the  
SETTING CLOCK  
B
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
CHANNEL SET UP  
“S”(Sexual Situation), or  
“V”(Violence). Then, press the  
F.FWD/B button to select  
[BLOCK] or [VIEW].  
Note: When you select [TV-MA], “D” does not  
appear on the TV screen.  
remote control.  
USERS SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
B
Press the PLAY/K or STOP/L but-  
ton to point to “V-CHIP SET UP”.  
Then, press the F.FWD/B button.  
INDEX SEARCH  
2 Select “TV RATING”  
Press the PLAY/K or STOP/L but-  
ton to point to “TV RATING”.  
Then, press the F.FWD/B button.  
The sub-ratings which set to  
[BLOCK] appears next to the rat-  
ing category in the TV RATING  
menu.  
V-CHIP SET UP –  
B
TV RATING  
MPAA RATING  
B
TVY  
TVY7  
TVG  
TVPG (DLSV)  
TV14 (DLSV)  
TVMA ( LSV)  
[VIEW]  
(
)
[VIEW]  
[VIEW]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
- 16 -  
EN  
8H30  
 
4 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
return to original mode.  
3 Select your desired item  
Press the PLAY/K or STOP/L but-  
ton to point to your desired item.  
Then, press the F.FWD/B button  
to select [BLOCK] or [VIEW].  
G
[VIEW]  
PG  
[VIEW]  
PG13  
R
NC17  
X
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
MPAA RATING SET UP  
Selection  
G
Rating Category Explanations  
General Audience  
Make sure ...  
TV/VCR power must be turned on.  
PG  
PG-13  
R
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
1 Select “V-CHIP SET UP”  
M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USERS SET UP  
Press the MENU button on the  
remote control.  
NC-17  
X
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “V-CHIP SET UP”.  
Then, press the F.FWD/B button.  
Mature audience only  
INDEX SEARCH  
When you select the rating category and turn it  
[BLOCK], the higher rating will turn [BLOCK]  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
V-CHIP SET UP –  
2 Select “MPAA RATING”  
Press the PLAY/K or STOP/L but-  
ton to point to “MPAA RATING”.  
Then, press the F.FWD/B button.  
TV RATING  
MPAA RATING  
B
When you turn “G” to [VIEW], then all ratings  
will turn to [VIEW] automatically.  
4 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
return to original mode.  
PLAYBACK  
This TV/VCR will operate with any cassette that has the  
mark. For best results, we  
recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.  
INSERTING A CASSETTE  
Insert the cassette in the direction as shown. Push in  
gently, but continuously, on the center-back of the  
cassette until it is drawn into the TV/VCR. The  
TV/VCR will automatically turn on.  
NORMAL PLAYBACK  
Make sure ...  
TV/VCR power must be turned on.  
1 Insert a prerecorded tape  
If the erase-protection tab has been removed, the  
TV/VCR will start playback automatically.  
Window  
WRONG  
B
PLAY  
CORRECT  
2 To begin playback  
Press the PLAY button.  
PRECAUTIONS  
Note: If any menu is activated on  
the screen, the PLAY button does  
not function. Press the MENU but-  
Avoid moisture. Moisture condensation may occur  
on the tape if it is moved from a cold place to a  
warm place or visa versa. Before using a tape with  
these conditions, to avoid damage of the tape and  
your TV/VCR, wait until the tape has warmed to  
room temperature and the moisture has evaporated.  
ton to clear the menu, then press the PLAY button.  
If a tape is already in the TV/VCR with the power  
off, do either of the following:  
A) Press the PLAY button on the TV/VCR. Power  
will automatically turn on and playback will start.  
B) Press the POWER button on the remote control to  
turn the TV/VCR on, then press the PLAY button  
on the remote control and playback will start.  
Avoid extreme heat, high humidity and magnetic  
fields.  
Do not tamper with the cassette mechanism.  
Do not touch the tape with your fingers.  
- 17 -  
EN  
8H30  
 
SEARCH  
STOP  
3 To stop playback  
Press the STOP button when play-  
back is completed.  
PICTURE SEARCH  
This feature is very useful in finding or skipping over  
a particular scene on a tape. In this mode, the sound  
will be muted.  
1)You may view a video tape at a high speed in  
either a forward or reverse direction by pressing  
the F.FWD or REW button during playback (in the  
SP / LP / SLP modes).  
2)Press it again and the TV/VCR will now search in  
super high speed (in the LP / SLP modes only).  
NOTE: Tapes recorded in the SP or LP mode will  
display a noise bar on the TV screen and the pic-  
ture may revert to Black and White. This is normal.  
3)Press the PLAY button to return to normal speed.  
AUTO REPEAT PLAYBACK  
The TV/VCR has an auto repeat function that allows  
you to repeat a tape indefinitely without touching the  
PLAY button.  
ALL REPEAT: Repeat playback from the beginning  
to the end of the tape.  
BLANK REPEAT: Repeat playback from the begin-  
ning to a blank part of more than 10 seconds.  
ZERO RETURN  
This function allows you to search easily a beginning  
point that you want to review by rewinding or fast  
forwarding.  
1 Select “USER’S SET UP”  
M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
remote control.  
SETTING CLOCK  
CHANNEL SET UP  
B
USERS SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
NOTE:  
Zero Return WILL NOT work on a blank tape or a  
blank portion of a tape.  
INDEX SEARCH  
2 Select “ALLor “BLANK”  
1 Stop a tape at your desired point  
Rewind or fast forward the tape to the beginning  
point from which you want to review.  
Press the PLAY/K or STOP/L button to point to  
“REPEAT PLAY”.  
USERS SET UP  
Press the F.FWD/B or REW/s  
button repeatedly until your desired  
selection [ALL] or [BLANK]  
appears.  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[ALL]  
[OFF]  
B
2 Reset the counter to 0:00:00  
Press the COUNTER RESET button repeatedly.  
3 Exit the Repeat Play setting  
Press the MENU button on the remote control to  
return to the TV mode.  
3 Begin recording or playback  
Press the RECORD or PLAY button.  
Press the STOP button when recording or playback is  
completed.  
4 Start playback  
Press the PLAY button to start the Repeat Play.  
”REPEAT PLAY B” appears.  
4 To activate “ZERO RETURN” mode  
Press the MENU button on the remote control.  
Press the PLAY/K or STOP/L button to point to  
Once you select the Repeat Play mode, it stays in  
effect even after you turn off the TV/VCR.  
If the Rental mode is set [ON], the “RENTAL  
PLAY B” display has priority.  
“ZERO RETURN”.  
Then, press the F.FWD/B button.  
The counter will appear on the TV  
screen.  
M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USERS SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
B
TIME SEARCH  
INDEX SEARCH  
The tape will automatically stop  
TO CANCEL THE REPEAT PLAY MODE  
when the counter returns to 0:00:00.  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
TIME SEARCH  
The Time Search function makes it possible to  
quickly advance the tape to your desired position  
simply by entering the exact amount of playback  
time you want to skip.  
- 18 -  
EN  
8H30  
 
NOTES:  
SLOW MOTION  
Time Search can be set up to a maximum of 9  
hours 50 minutes (9:50) by 10 minutes at a time.  
Press the SLOW button to reduce the playback speed.  
The TV/VCR mutes the sound during slow motion.  
Press the PLAY button to return to normal playback.  
NOTE: If left in the Slow mode for more than five  
minutes, the TV/VCR will automatically go into the  
Stop mode.  
This function will not operate in recording mode.  
In the example below: To watch a program that is 2  
hours, 50 minutes from the present tape position, in  
either direction.  
1 Insert a tape.  
RENTAL PLAYBACK  
2 Select “TIME SEARCH” mode  
Press the TIME SEARCH button (with each push it  
will increase by 10 minute).  
This function enables you to improve the picture  
quality when playing back worn cassettes such as  
rented tapes.  
3 Enter your desired time  
TIME SEARCH  
2 : 50  
1 Select “USER’S SET UP”  
Press the PLAY/K or STOP/L but-  
M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
ton until your desired time appears.  
(Example: “2:50” stands for 2 hours  
50 minutes)  
If you wish to cancel the Time Search at this point,  
press the MENU button on the remote control.  
PICTURE CONTROL  
SETTING CLOCK  
remote control.  
CHANNEL SET UP  
B
USERS SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
INDEX SEARCH  
USERS SET UP  
2 Set “RENTALto [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “RENTAL”.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
4 Begin Time Search  
By pressing the REW/s or F.FWD/B button, the  
TV/VCR will rewind or fast forward to the specified  
point.  
B
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[ON]  
[OFF]  
[OFF]  
The time counts down as the searching progresses.  
When 0:00 is reached, the tape will start playback  
automatically.  
3 Exit the Rental setting  
Press the MENU button on the remote control to  
return to the TV mode.  
TO CANCEL THE TIME SEARCH at this  
point  
Press the STOP/EJECT button on the TV/VCR or the  
remote control. This will delete the selected time.  
4 Start playback  
Press the PLAY button to start playback. “RENTAL  
PLAY B” appears.  
Once you select the Rental mode, it stays in effect  
even after you turn off the TV/VCR.  
INDEX SEARCH  
An index signal is recorded on the tape automatically  
when the recording is started. To view a recording at a  
specific start point:  
1)Press the MENU button on the  
CHANNEL SET UP  
remote control. Press the  
USERS SET UP  
PLAY/K or STOP/L button to  
point to “INDEX SEARCH”,  
then press the F.FWD/B button.  
2)Press the PLAY/K or STOP/L button within 30  
seconds until the number of programs that you  
want to skip appears.  
TO CANCEL THE RENTAL MODE  
M E N U –  
TIMER PROGRAMMING  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
PICTURE CONTROL  
SETTING CLOCK  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
B
3)Press the F.FWD/B or REW/s button to start  
index search. If you want to go forward, press the  
F.FWD/B button. If you want to go back, press  
the REW/s button.  
After index search, the TV/VCR will play the tape  
automatically.  
In some cases, the index mark at the beginning of  
video tape cannot be detected.  
- 19 -  
EN  
8H30  
 
VERTICAL HOLD CONTROL  
TRACKING ADJUSTMENT  
In the Pause/Still mode only, when the picture begins  
to vibrate vertically, stabilize the picture by pressing  
the CHANNEL K or L button.  
Tracking adjustment will be set automatically  
(Digital Tracking function) when you start play-  
back.  
NOTE:  
However when playing pre-recorded tapes or tapes  
recorded on units other than your own, noise lines  
(black and white streaks) may appear on the play-  
back picture. If this occurs, you can adjust the  
tracking control manually by pressing the CHAN-  
NEL K or L button until the streaks disappear. To  
return to the DTR function, stop the tape once and  
start playback again.  
You can reduce the noise lines by pressing the  
CHANNEL K or L button in slow mode, too.  
Tracking adjustment in Slow mode will not be set  
automatically.  
If there are video noise lines on the screen, see Tracking  
Adjustment section.  
STILL PICTURE  
You can view a still picture on the TV screen during  
playback (the Still mode). Press the PAUSE/STILL  
button during playback. Only tapes recorded in the  
SLP mode will show the least amount of lines. Press  
the PLAY button to return to playback.  
NOTES:  
You can advance the picture one frame at a time by  
pressing the PAUSE/STILL button during the Still  
mode.  
If it is left in the Still mode for more than five min-  
utes, the TV/VCR will automatically switch to the  
Stop mode.  
NOTE:  
In Still mode, press the SLOW button and press the  
CHANNEL K or L button until streaks disappear.  
To return to Still mode, press the PAUSE/STILL  
button again.  
RECORDING  
Make sure ...  
Before recording, make sure:  
TV/VCR power is turned on.  
The desired channel is selected by pressing the num-  
ber buttons on the remote control or the CHANNEL  
Up/Down button. (If the TV/VCR is connected to a  
cable box or satellite box, the TV/VCR must be on  
CH3 or CH4, then the channel to be recorded is  
selected on the cable box or satellite box. )  
There is a tape with its safety tab into the VCR.  
The desired recording speed is selected in SP(stan-  
dard play) or SLP(super long play) mode by press-  
ing the TAPE SPEED button on the VCR.  
Insert a cassette tape with its erase prevention tab  
in place. (If necessary, rewind or fast forward the  
tape to the point at which you want to begin  
recording.)  
NOTE: This unit will ONLY record and view the  
same channel.  
NORMAL RECORDING  
1)Begin the recording by pressing the RECORD but-  
ton.  
Tape Speed  
Type of tape  
SP mode  
Recording/Playback Time  
T60  
1 hour  
3 hours  
T120  
T160  
To temporarily stop recording or resume it, press  
the PAUSE/STILL button. After the VCR has been  
in Pause mode for 5 minutes, it will stop automati-  
cally to protect the tape and the video head.  
NOTES:  
2 hours 2-2/3 hours  
6 hours 8 hours  
SLP mode  
ERASE PREVENTION  
You can prevent acciden-  
tal erasing of recording  
by breaking off the tab  
on the back edge of the  
cassette.  
After five minutes, the TV/VCR will automatically  
switch to the Recording mode to prevent tape  
damage.  
If “CLOSED CAPTION (ON)” is selected, the  
On-Screen Display will appear for 5 seconds, then  
disappear.  
If you decide to record  
on the tape again, cover  
the hole with plastic  
tape.  
2)Stop the recording by pressing the STOP button  
when recording is completed.  
Tab  
Plastic Tape  
- 20 -  
EN  
8H30  
 
AAvoid overlap of programs ...  
There is a chance that a program will not be record-  
ed. When programs overlap:  
OTR (One Touch Recording)  
This function enables you to set the recording length  
simply by pressing the REC/OTR button on the  
VCR.  
The program with the earliest start time will record  
first.  
Once the earliest program finishes recording, the  
overlapping programs will record in the order of  
the program number.  
The illustration below demonstrates the sequence  
of recording.  
1)Begin OTR by pressing the  
OTR(2 : 30)  
REC/OTR button on the VCR  
repeatedly until the desired  
recording length appears.  
Recording stops when 0:00 is  
SP  
reached.  
Recording Sequence  
NOTES:  
Program 1  
10:00AM-11:00AM  
Program 2  
9:00AM-10:00AM  
Program 3  
This function CANNOT be done from the remote  
control.  
9:30AM-12:00PM  
To stop the OTR operation, press the STOP button  
on the TV/VCR or on the remote control.  
9:00AM  
10:00AM  
11:00AM  
12:00PM  
*Recording period is SHADED  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, eject the tape and turn itself off.  
1 Select “TIMER PROGRAMMING”  
Press the MENU button on the  
M E N U –  
Push(es) Display  
1 push  
Recording length  
(continuous recording)  
30 minutes  
B
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USERS SET UP  
remote control.  
Confirm “TIMER PROGRAM-  
MING” is pointed to by pressing  
the PLAY/K button.  
V-CHIP SET UP  
2 pushes  
3 pushes  
4 pushes  
0:30  
1:00  
1:30  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
60 minutes  
90 minutes  
TIME SEARCH  
INDEX SEARCH  
Press the F.FWD/B button.  
If you have not yet set the clock, “MANUAL  
CLOCK SET” appears. If so, follow stops [3] to  
[8] on page 11. Then set the timer recording.  
17 pushes  
8:00  
480 minutes  
TIMER RECORDING  
2 Select your desired program position (1~8)  
You may set the TV/VCR to start and end a record-  
ing while you are away. You can set 8 programs to  
record on specific days, daily or weekly within a 1  
year period.  
TIMER PROGRAMMING –  
Press the PLAY/K or STOP/L  
button to select the desired pro-  
gram position.  
CH DATE  
BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
Then, press the F.FWD/B button.  
In the example below, the timer is being set to record:  
DATE:  
July 6th, 2001  
SETTING TIME: from 7:30PM to 8:50PM  
3 Set the channel number  
CHANNEL:  
TAPE SPEED:  
CH61  
SP  
Press the PLAY/K or STOP/L button until the  
desired channel number appears.  
(Example: CH61)  
Then, press the F.FWD/B button.  
Remember:  
If your TV/VCR is connected to a  
cable or satellite box, you must set  
TIMER PROGRAMMING –  
CH DATE BEGIN END  
Make sure ...  
If your TV/VCR is connected to a cable or satellite  
box, you must set the TV/VCR to channel 3 or 4  
to match the output channel of the box.  
Clock is set to the correct time and date before set-  
ting the timer.  
TV/VCR power is turned on to program it.  
To insert a cassette tape with its erase prevention  
tab in place. (If necessary, rewind or fast forward  
the tape to the point at which you want to begin  
recording.)  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
the TV/VCR to channel 3 or 4 to match the output  
channel of the box.  
4 Select once, every day or weekly recording  
For once recording :  
TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
To set the channel you want to record  
Press the PLAY/K (up) button  
until the desired date appears.  
(Example: “7/06” for July 6th).  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 7/06 FRI -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
- 21 -  
EN  
8H30  
 
For every day recording : To  
record a TV program at the same  
time on the same channel every  
day. (Example: Monday through  
Sunday)  
TIMER PROGRAMMING –  
CH DATE BEGIN END  
10 Finish setting the program  
Press the F.FWD/B or REW/s button. The program  
is now completed.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY DAY -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
To set another program, repeat steps [2] to [10].  
Press the MENU button on the remote control to  
Press the STOP/L (down) but-  
ton until “EVRY DAY” appears. Then, press the  
F.FWD/B button.  
return to original mode.  
11 Set the timer  
For weekly recording : To record a TV program at  
the same time on the same channel every week.  
Press the POWER button to set automatic timer  
recording. The TIMER REC indicator lights up.  
(Example: every Monday)  
You must turn off the TV/VCR to activate automat-  
ic timer recording.  
TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Press the STOP/L (down) button  
until “EVRY” and your desired  
day of the week appear together.  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
If power is not turned off and you continue watch-  
ing TV, TIMER REC STANDBY” starts flashing  
on the TV screen 2 minutes before the programmed  
start time.  
B
TIMER PROGRAMMING –  
CH DATE BEGIN END  
5 Set beginning hour  
TIMER PROGRAM EXTENSION  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “ 7, PM” for 7:30PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/06 FRI 7:12P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
To shift the time schedule of an automatic timer  
recording.  
1)Press the POWER button.  
2)Repeat step [1] on page 21.  
6 Set beginning minute  
TIMER PROGRAMMING –  
CH DATE BEGIN END  
3)Press the RECORD button and select the desired  
program using the PLAY/K or STOP/L button.  
4)Press the RECORD button again.  
Each additional push will shift forward the  
begin/end time for recording by 10 minutes. When  
the recording is already in progress, each additional  
push will shift forward the end time only. If you  
want to cancel while setting, press the  
PAUSE/STILL button on the remote control. The  
recording time returns to the original time.  
NOTE: When you shift forward the time schedule  
during recording, the recording speed will automati-  
cally be set to the SLP mode.  
Press the PLAY/K or STOP/L but-  
ton until the desired minute appears.  
(Example: “30” for 7:30PM)  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/06 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
Then, press the F.FWD/B button.  
TIMER PROGRAMMING –  
CH DATE BEGIN END  
7 Set end hour  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “8, PM” for 8:50PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:30PM - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/06 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
TIMER PROGRAMMING –  
CH DATE BEGIN END  
8 Set end minute  
5)Press the F.FWD/B or REW/s button to exit the  
setting menu. Then press the MENU button on the  
remote control to return to original mode.  
Press the PLAY/K or STOP/L but-  
ton until the desired minute appears.  
(Example: “50” for 8:50PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PM- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/06 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
TO CORRECT A PROGRAM  
While setting a program; press the REW/s but-  
ton to go back one step and enter the correct num-  
TIMER PROGRAMMING –  
CH DATE BEGIN END  
9 Set the tape speed  
Press the PLAY/K or STOP/L but-  
ton until the desired tape speed  
appears. (Example: SP)  
bers using the PLAY/K or STOP/L button.  
After setting a program;  
1)Press the POWER button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PMSP  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/06 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
2)Repeat steps [1] - [2] on page 21.  
3)Press the F.FWD/B button (or press the REW/s  
button to go back one step) until the part you  
want to correct begins flashing, then make the  
changes pressing the PLAY/K or STOP/L but-  
ton.  
4)Press the POWER button to set automatic timer  
recording.  
- 22 -  
EN  
8H30  
 
TO CANCEL AN AUTOMATIC TIMER  
RECORDING  
USERS SET UP  
2 Set “AUTO RETURN” to [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO RETURN”.  
Press the F.FWD/B or REW/s  
button until [ON] appears. Then,  
After setting a program;  
1)Press the POWER button.  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[OFF]  
[ON]  
B
2)Repeat steps [1] ~ [2] under TIMER RECORD-  
ING, page 21, and select a program you want to  
cancel.  
3)Press the T-PROG. CLEAR button.  
4)Press the MENU button on the remote control to  
return to TV mode.  
press the MENU button on the remote control to  
return to TV mode.  
3 Auto Return will begin  
While recording is in progress;  
1)Press POWER button.  
When all the timer recordings are completed, the  
TV/VCR will rewind to the beginning of the recorded  
2)Press the STOP/EJECT button on the TV/VCR.  
program(s).  
NOTE:  
TO CHECK THE BEGIN/END TIME  
1)Press the POWER button so that the REC indicator  
goes off.  
If you press the POWER button while tape is  
rewinding, the Auto Return will stop.  
2)Press the MENU button on the remote control.  
3)Confirm “TIMER PROGRAMMING” is pointed  
to.  
4 Watch the recorded program  
Press the PLAY button.  
4)Press the F.FWD/B button. The details of pro-  
grams appear on the TV screen.  
5)Press the MENU button on the remote control to  
return to TV mode.  
TO CANCEL THE AUTO RETURN  
MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button. Then, press the MENU  
button on the remote control to return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
HINTS FOR AUTOMATIC  
TIMER RECORDING  
Make sure the channel you want to record is prop-  
erly set in advance.  
It is not necessary to press the RECORD button for  
timer recording.  
WAKE UP TIMER  
Recording begins automatically at the Start time.  
If you are recording using a Timer mode, you may  
not operate the unit manually.  
The Wake Up Timer function turns on the TV/VCR  
without using the POWER button after a desired  
period of time.  
The erase-prevention tab on the cassette must be in  
place (or you must put tape over the hole).  
If the erase-prevention tab is removed, the cassette  
will be ejected when the POWER button is pressed  
to off.  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, and the tape will be ejected.  
NOTES:  
Use the remote control for this procedure.  
Clock must be set to the correct time before setting  
the timer.  
If you want to select [TAPE], you must insert a  
cassette tape in the TV/VCR. The tape will start  
playback automatically on your desired time.  
1 Select “WAKE UP TIMER”  
Press the WAKE-UP/SLEEP button  
on the remote control once, and  
confirm “ON/OFF” is pointed.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
AUTO RETURN  
With this feature, after timer recording is finished,  
the beginning of the recorded program(s) can be  
searched for automatically.  
WAKE UP B ON/OFF  
[ON]  
TIMER  
TV/TAPE  
TIME  
[TV]  
[12:00AM]  
M E N U –  
1 Select “USER’S SET UP”  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
Press the MENU button on the  
CHANNEL SET UP  
B
USERS SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
INDEX SEARCH  
- 23 -  
EN  
8H30  
 
SLEEP TIMER  
2 Select “TV” or “TAPE”  
The Sleep Timer function turns off the TV/VCR  
without using the POWER button after a desired  
period of time.  
Press the PLAY/K or STOP/L but-  
ton until it points to “TV/TAPE”.  
Press the F.FWD/B or REW/s  
button, and select [TV] or [TAPE].  
WAKE UP  
TIMER  
ON/OFF  
B TV/TAPE  
TIME  
[ON]  
[TV]  
NOTE:  
[12:00AM]  
This function does not operate during Recording  
mode.  
3 Set wake up time  
1 Select “SLEEP TIMER”  
Press the PLAY/K or STOP/L but-  
ton until it points to “TIME”.  
Press the F.FWD/B or REW/s  
button until your desired wake up  
time appears.  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
WAKE UP  
TIMER  
ON/OFF  
TV/TAPE  
B TIME  
[ON]  
[TV]  
[12:00AM]  
2 Set sleep time  
Press the PLAY/K, STOP/L,  
F.FWD/B or REW/s button until  
your desired sleep time appears.  
Each additional push will increase (or decrease) the  
time by 10 minutes.  
SLEEP TIMER [2:00]  
Each additional push will increase  
4 Exit the Wake Up Timer setting  
Press the MENU button on the remote control to  
return to TV mode.  
the time by 30 minutes up to 120 minutes.  
Press the MENU button on the remote control to exit  
the Sleep Timer setting.  
TO CANCEL THE WAKE UP TIMER  
TO CANCEL THE SLEEP TIMER  
Press the WAKE-UP/SLEEP button on the remote  
control once, and confirm “ON/OFF” is pointed.  
Press the F.FWD/B or REW/s button until [OFF]  
appears.  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
To view the time left for sleep timer, press the  
WAKE-UP/SLEEP button twice, then press the  
MENU button on the remote control to exit the sleep  
timer setting.  
COPYING A VIDEO TAPE  
You can make copies of video tapes made by friends  
or relatives for your enjoyment.  
1)Insert a pre-recorded video cassette into the Source  
(Playing) VCR or camcorder.  
2)Insert a blank video cassette, or one you want to  
record over, into the TV/VCR’s cassette compart-  
ment.  
3)Press the SPEED button on remote control for the  
TV/VCR to select the desired recording speed  
(SP/SLP).  
WARNING: Unauthorized recordings of  
copyrighted video tapes may be an  
infringement of copyright laws.  
Connect your TV/VCR and a Source (Playing) VCR  
using the following diagram.  
4)Press the CHANNEL K or L button on the  
TV/VCR until “AUX” appears on the screen.  
NOTE: “AUX” is found below the lowest numbered  
memorized channel. (Example: CH2)  
5)Press the RECORD button on the TV/VCR.  
6)Begin playback of the tape in the source (Playing)  
VCR or camcorder.  
AUDIO  
VIDEO  
STOP/EJECT  
[The TV/VCR]  
NOTE: For best results during copying, use the  
TV/VCR’s front panel controls whenever possible.  
The remote control might affect the source (Playing)  
VCR’s playback operation.  
[Ex: Source (playing)  
VCR or camcorder]  
VIDEO  
Audio/Video  
adapter cable  
(not supplied)  
OUT  
IN  
AUDIO  
- 24 -  
EN  
8H30  
 
ON SCREEN DISPLAY  
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote  
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:  
WHEN THE CLOSED CAPTION MODE IS OFF:  
<Off mode>  
<Counter mode>  
<Clock mode>  
Counter mode: After 5 seconds, only  
the counter remains. To clear it, press  
the DISPLAY button.  
Clock mode: After 5 seconds, only  
the clock and the channel number  
remain. To clear them, press the DIS-  
PLAY button.  
5:40PM  
CH2  
Press  
once  
Press  
once  
COUNT 0:12:34  
Press once  
OFF mode  
Clock/Counter mode  
WHEN THE CLOSED CAPTION MODE IS ON:  
The On Screen Display disappears after 5 seconds.  
STOP  
5:40 PM  
CH2  
This is true even if the MUTE button is pressed, or the  
PAUSE/STILL button is pressed while recording.  
SP  
COUNT 0:12:34  
SPECIAL FEATURES  
REAL TIME TAPE COUNTER  
AUTO REWIND-EJECT  
This shows the elapsed recording or playback time in  
When the end of a tape is reached during record-  
ing, playback, or fast-forward, the tape will auto-  
matically rewind to the beginning. After rewinding  
finishes, the TV/VCR will eject the tape and turn  
itself to off.  
This function is operative when Repeat Play is set  
to the [OFF] position.  
hours, minutes, and seconds. (The displayed time  
will not change on a blank tape or blank portions on  
the tape.)The “–” indication will appear when the  
tape has rewound further than “0:00:00” on the tape  
counter.  
The tape will not auto-rewind during timer record-  
ing or One Touch Recording.  
MAINTENANCE  
back, the video heads in your TV/VCR may need  
to be cleaned.  
CABINET CLEANING  
Wipe the front panel and other exterior surfaces of  
the TV/VCR with a soft cloth immersed in luke-  
warm water and wrung dry.  
1.Please visit your local Audio/Video store and pur-  
chase a good quality VHS Video Head Cleaner.  
2.If a Video Head Cleaner does not solve the prob-  
lem, please call our help line at 1-800-968-3429, to  
locate an Authorized Service Center.  
NOTES:  
Remember to read the instructions included with  
the video head cleaner before use.  
Clean video heads only when problems occur.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the TV/VCR. Such chemicals  
may cause damage and discoloration to the  
exposed surfaces.  
AUTO HEAD CLEANING  
Automatically cleans video heads as you insert or  
remove a cassette, so you can see a clear picture.  
SERVICING  
Should your TV/VCR become inoperative, do not  
try to correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug the  
power cord, and please call our help line at 1-800-  
968-3429, to locate an Authorized Service Center.  
Playback picture may become blurred or interrupt-  
ed while the TV program reception is clear. Dirt  
accumulated on the video heads after long periods  
of use, or the usage of rental or worn tapes can  
cause this problem.  
If a streaky or snowy picture appears during play-  
- 25 -  
EN  
8H30  
 
TROUBLESHOOTING GUIDE  
If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,  
locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to  
remedy the problem.  
PROBLEM  
CORRECTIVE ACTION  
No power.  
Make sure the AC cord is connected to an AC outlet.  
Make sure the car battery cord is connected to vehicle’s cigarette  
lighter socket and to DC 13.2V (12V) jack on back of the TV/VCR.  
Check the fuse (5A, 250V) in car battery cord.  
Make sure the power is turned on.  
Make sure the AC cord is connected to an AC outlet.  
Check antenna connection.  
Let the TV/VCR program its tuner memory.  
Adjust direction or replace antenna.  
Adjust picture controls.  
Adjust volume control on remote control or main unit.  
Press the MUTE button to restore sound.  
Make sure the timer recording is set correctly.  
Make sure the power is off.  
No picture and sound.  
No picture or poor picture on  
TV/VCR.  
No sound or poor sound.  
Timer recording is not possible.  
Make sure the TV/VCR clock is set correctly.  
Make sure the tape has an erase-prevention tab. If need, cover the  
hole with plastic tape.  
Cannot go into Record mode.  
Playback picture is partially noisy.  
Adjust tracking control for a better picture using the CHANNEL  
or L button on the TV/VCR.  
K
No picture but the audio is OK in  
playback.  
No operation by infrared Remote  
Control.  
Video or color fades in and out  
when making a copy of a video tape  
Head cleaning may be necessary. Refer to “AUTO HEAD  
CLEANING” on page 25.  
Make sure the AC cord is connected to an AC outlet.  
Check batteries in remote control.  
You can not copy a copyrighted video tape. You are experiencing  
copy guard protection.  
Make sure the AC cord is connected to an AC outlet.  
.
Cannot set the auto clock to ON.  
CLOSED CAPTION PROBLEM  
My TV/VCR is showing captions  
that are misspelled.  
POSSIBLE REMEDY  
You are watching a live broadcast and spelling errors made by the  
closed captioning production company may pass through uncorrected.  
A prerecorded program will not show any misspelled words because  
of the normal time available for editing the captions.  
My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue  
in its entirety or there is a delay of are common for live broadcast. Most captioning production companies  
what is being said.  
can display a dialogue to a maximum of 220 words per minute. If a  
dialogue exceeds that rate, selective editing is used to insure that the  
captions remain up-to-date with the current TV screen dialogue.  
• Interference caused by building, power lines, thunderstorms, etc.  
may cause scrambled or incomplete captions to appear.  
My captions are scrambled with  
white boxes on the TV screen.  
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed  
as being closed captioned but none up the actual program so that additional advertising time can be  
of the captions were displayed.  
given. Since the decoder cannot read the compressed information,  
captions will be lost.  
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating  
show any captions. The tape box company accidentally left out the captioning signals during the  
mentions it being closed captioned. copying process.  
My TV screen shows a black box  
on certain channels.  
You are in the TEXT mode. Select CAPTION mode to CAPTION  
[OFF].  
- 26 -  
EN  
8H30  
 
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
Video input level :  
Audio input level :  
0.5~2.0Vp-p  
-15dBs  
CRT :  
13 inch in-line gun, 90˚  
deflection tube  
NTSC-M  
Video S/N ratio : More than 46dB  
Audio S/N ratio : More than 43dB  
Television system :  
Closed caption system :§15.119/FCC  
Video Heads :  
Tape width :  
Tape speed  
SP :  
LP :  
SLP :  
Tuner channel  
TV VHF Low :  
TV VHF High :  
TV UHF :  
CATV  
Rotary four-head  
1/2 inch  
OTHER SPECIFICATIONS  
Power requirement : AC 120V/60Hz  
DC 13.2V  
33.40mm/sec.  
16.67mm/sec.  
11.12mm/sec.  
Power consumption : AC 65W / DC 75W  
Dimensions :  
H:15-13/16” (402mm)  
W:15-3/16” (386mm)  
D:14-7/8” (378mm)  
27.6 lbs (12.5kg)  
#2~#6  
#7~#13  
#14~#69  
Weight :  
VHF :  
5A  
Designs and specifications are subject to change  
without notice and without our legal obligation.  
If there is a discrepancy between languages, the  
default language will be English.  
MID band :  
SUPER band :  
HYPER band :  
Terminals  
A5~A1, A~I  
J~W  
W+1~W+84  
Antenna input :  
VHF/UHF 75 ohms  
unbalanced  
Video input :  
Audio input :  
Earphone :  
RCA connector [ 1  
RCA connector [ 1  
1/8” monaural (3.5 mm)  
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
TV Display  
31  
32  
33  
34  
35  
36  
CATV channel  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
TV Display  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
W+55 W+56 W+57 W+58  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
91  
92  
93  
94  
CATV channel  
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
TV Display  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
- 27 -  
EN  
8H30  
 
INDICE  
CONTROLES DE OPERACIÓN Y  
SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28  
INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .31  
PREPARACIÓN DE CANALES POR  
CONEXIONES DE ANTENA/CABLE . . . . . . . .30 PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31  
MODO DE ENTRADA EXTERNA . . . . . . . . . . .31 AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31  
CONTROLES DE OPERACIÓN Y SUS FUNCIONES  
NOTA:  
No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un  
mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el  
número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del  
mando a distancia universal.  
- PANEL DELANTERO -  
AUDIO  
VIDEO  
STOP/EJECT  
REW  
PLAY F.FWD  
REC/OTR  
CHANNEL  
VOLUME  
POWER  
1
2
3
4
5
6
7
8 9 10  
11  
12 13  
14  
[ Televisor/videograbadora ]  
4 Botón de parada (STOP)– Púlselo para detener la  
cinta.  
- CONTROL REMOTO -  
25  
4
Botón de expulsión (EJECT)–Púlselo en el modo  
de parada para expulsar la cinta del  
televisor/videograbadora.  
WAKE-UP  
POWER  
/SLEEP  
EJECT  
13  
15  
CHANNEL  
RETURN  
Botón L–  
1
4
7
2
5
8
3
6
9
24  
Púlselo para seleccionar los modos de ajuste desde el  
menúde la pantalla.  
Púlselo para introducir dígitos cuando establezca un  
programa.  
(Por ejemplo: Para ajustar el reloj o establecer un pro-  
grama de temporizador)  
[ Control remoto ]  
CHANNEL  
VOLUME  
11  
12  
0
+100  
MENU  
DISPLAY  
MUTE  
16  
17  
5
23  
6
PLAY  
7
REW  
F.FWD  
4 Botón de expulsión (EJECT)–Púlselo en el modo  
de parada para expulsar la cinta del  
STOP  
4
RECORD  
SPEED PAUSE/STILL  
televisor/videograbadora.  
22  
21  
8
18  
T-PROG.  
CLEAR  
GAME  
SLOW  
5 Botón de rebobinado (REW)– Púlselo para rebobi-  
nar la cinta, o para ver la imagen en retroceso rápido  
durante el modo de reproducción. (Búsqueda con  
rebobinado)  
COUNTER  
RESET  
19  
20  
Botón s–  
1 Toma de auriculares (EARPHONE)– Para conec-  
tar los auriculares (no suministrados) y escuchar en pri-  
vado. La toma es mono y tiene un tamaño de 3,5 mm.  
2 Toma de entrada de audio (AUDIO)– Conéctela a  
la toma de salida de audio de su equipo de audio,  
videocámara u otra videograbadora.  
3 Toma de entrada de vídeo (VIDEO)– Conéctela a  
la toma de salida de vídeo de su videocámara u otra  
videograbadora.  
Púlselo para seleccionar un modo desde un menúpar-  
ticular.  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
6 Botón de reproducción (PLAY)– Púlselo para ini-  
ciar la reproducción.  
Botón K–  
Púlselo para seleccionar los modos de ajuste desde el  
menúde la pantalla.  
- 28 -  
ES  
0I29  
 
- PANEL TRASERO -  
DC 13.2V  
AC 120V  
ANT.  
26  
27 28  
Púlselo para introducir dígitos cuando establezca un  
programa.  
(Por ejemplo: Para ajustar el reloj o establecer un pro-  
grama de temporizador)  
7 Botón de avance rápido (F.FWD)– Púlselo para  
avanzar rápidamente la cinta, o para ver la imagen en  
avance rápido durante el modo de reproducción.  
(Búsqueda con avance rápido)  
14 Compartimiento del videocasete  
15 Botones numerados– Púlselos para seleccionar los  
canales deseados para ver o grabar. Para seleccionar  
canales del 1 al 9, pulse primero el botón 0 y luego el  
botón 1 a 9.  
Botón +100– Cuando seleccione canales de tele-  
visión por cable cuyo número sea superior al 99, pulse  
primero este botón, y luego pulse los dos últimos dígi-  
tos. (Para seleccionar el canal 125, pulse primero el  
botón “+100” y luego el “2” y el “5”.)  
Botón B–  
Cuando establezca un programa (por ejemplo: para  
ajustar el reloj o para establecer un programa de tem-  
porizador), púlselo para determinar su elección y vaya  
al paso siguiente que quiera introducir.  
Púlselo para determinar los modos de ajuste desde el  
menúde la pantalla.  
16 Botón de menú (MENU)– Púlselo para visualizar el  
menúprincipal en la pantalla del televisor.  
17 Botón del visualizador (DISPLAY)– Visualiza el  
contador o el número del canal actual y la hora actual  
en la pantalla del televisor.  
18 Botón de velocidad de cinta (SPEED)– Púlselo  
Púlselo para seleccionar un modo desde un menúpar-  
ticular.  
para elegir la velocidad de grabación deseada: SP/SLP.  
19 Botón T-PROG. CLEAR– Púlselo para cancelar un  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
8 Botón de grabación (REC)– Púlselo para iniciar la  
grabación manual.  
Botón de grabación de un toque (OTR)– Activa  
la grabación de un toque. (Sólo en el  
televisor/videograbadora)  
programa de temporizador.  
Botón de reposición del contador (COUNTER  
RESET)– Púlselo para reponer el contador a 0:00:00.  
20 Botón de juego (GAME)– Establece el modo del  
juego y el modo de entrada externa al mismo tiempo.  
21 Botón de cámera lenta (SLOW)– Pulselo para  
9 Indicador de grabación (RECORD)– Parpadea  
durante la grabación.  
activar la reproducción a cámera lenta.  
22 Botón de pausa/imagen fija (PAUSE/STILL)–  
Púlselo para detener temporalmente la cinta durante la  
grabación o para ver una imagen fija durante la repro-  
ducción.  
Se enciende en el modo de espera de la grabación con  
temporizador.  
10 Ventanilla sensora del mando a distancia–  
Recibe las señales infrarrojas procedentes del mando a  
distancia.  
11 Botones de canales (CHANNEL K/ L)– Púlselos  
para seleccionar los canales deseados para ver o  
grabar.  
23 Botón de silenciamiento (MUTE)– Silencia el  
sonido. Púlselo de nuevo para recuperar el sonido.  
24 Botón de retorno de canal (CHANNEL  
RETURN)– Púlselo para volver al canal anterior. Por  
ejemplo, pulsando una vez este botón, la visualización  
del canal cambiará de 3 (canal actual) a 10 (canal ante-  
rior), y al pulsarlo por segunda vez, el canal cambiará  
del 10 al 3.  
25 Botón del temporizador despertador/para  
dormir (WAKE-UP/SLEEP)– Ajusta el tempo-  
rizador para despertarse/dormir.  
Se puede mostrar el menú principal en la pantalla del  
televisor pulsando repetidamente este botón del televi-  
sor/videograbadora.  
Función de seguimiento– Pulse los botones para  
minimizar el ruido de vídeo (líneas o puntos en la pan-  
talla) durante la reproducción.  
12 Botones de volumen (VOLUME X / Y)– Ajustan  
26 Cordón de alimentación– Conéctelo a la toma de  
el nivel del volumen.  
CA estándar (120V/60Hz).  
13 Botón de la alimentación (POWER)– Púlselo  
para encender y apagar el televisor/videograbadora.  
Púlselo para activar la grabación con temporizador.  
27 Terminal de antena (ANT.)– Para conectar una  
antena o sistema de televisión por cable.  
- 29 -  
ES  
0I29  
 
CONEXIONES DE ANTENA/CABLE  
Desde el cable coaxial o  
caja de emisiones vía  
satélite de 75 ohm del  
sistema de Cable  
Caja de CATV  
o caja de emi-  
siones vía satélite  
(no incluído)  
Antena combinada de  
VHF/UHF  
(no incluído)  
Antena de varilla UHF/VHF  
(incluído)  
OUT  
IN  
Antena VHF  
(no incluído)  
Desde el  
sistema de Cable  
Antena UHF  
(no incluído)  
o
DC 13.2V  
AC 120V  
ANT.  
Combinador de  
o
VHF/UHF  
(no incluído)  
ANT.  
Cable coaxial  
de 75 ohm (no incluído)  
o
o
PARA GRABAR UN CANAL  
ANTENA COMBINADA DE VHF/UHF  
La antena de varilla de VHF/UHF (incluído) es  
desmontable. Inserte el vástago de la antena en el agujero  
de la parte trasera superior del televisor/videograbadora.  
Conecte la varilla de antena de VHF/UHF o la antena com-  
binada de VHF/UHF al terminal ANT. del  
televisor/videograbadora.  
CODIFICADO/DESCODIFICADO  
1. Ajuste el selector de canales del televisor/videograbado-  
ra al canal de salida del convertidor de televisión por  
cable o del convertidor de emisiones vía satélite. (Ej.:  
CA3)  
2. Seleccione el canal que desee grabar de su convertidor  
de televisión por cable o del convertidor de emisiones  
vía satélite.  
ANTENAS SEPARADAS DE VHF/UHF  
En algunos lugares será necesario utilizar una antena exte-  
rior.  
CONEXION MOVIL  
CABLE SIN CONVERTIDOR/DESCODIFICADOR  
ADVERTENCIA: El conductor nunca debe ver programas  
del televisor o del videobgrabadora mientras está con-  
duciendo un vehículo.  
PRECAUCIÓN: Si usted usa la TV/VCR con el motor del  
vehículo apagado, recargue la batería del vehículo aprox.  
cada 4 horas de uso, para evitar que ésta se agote. Cuando  
termine de usar la TV/VCR, siempre desenchufe el cordón  
para la batería del automóvil del zócalo del encendedor de  
cigarrillos.  
Utilice esta conexión si su sistema de televisión por cable  
se conecta directamente a su televisor/videograbadora sin  
convertidor.Utilizando esta conexión usted podrá:  
1)Utilizar el mando a distancia del televisor/videograbado-  
ra para seleccionar canales.  
2)Programar uno o más canales sin codificar para realizar  
la grabación automática con temporizador.  
1) La antena de interiores incluída es adecuada para usar cuando  
el vehículo está inmóvil. Para obtener una mejor recepción en  
ruta, utilice una antena de VHF/UHF para TV móvil de alta  
calldad.  
2) Enchufe el cordón para batería de automóvil al conector DC13.2V  
(12V) en la parte posterior de la TV/VCR. Luego conecte el otro  
extremo en el zócaio para el encendedor de cigarrillos del  
automóvil.  
NOTA: Con esta unidad SÓLO se podrá grabar y ver un  
mismo canal al mismo tiempo.  
CABLE CON CONVERTIDOR/DESCODIFICADOR  
O CONVERTIDOR DE EMISIONES VÍA SATÉLITE  
Si su servicio de televisión por cable le suministra un con-  
vertidor, o si usted utiliza un sistema de emisiones vía  
satélite, usted podrá utilizar las conexiones básicas.  
NOTAS:  
Utilizando estas conexiones, usted también podrá grabar  
canales codificados. Sin embargo, la selección de los  
canales deberá hacerse con el convertidor de televisión por  
cable con el convertidor de emisiones vía satélite. Esto sig-  
nifica que los canales no podrán ser cambiados con el  
mando a distancia del televisor/videograbadora. La  
grabación inatendida se limita a un canal cada vez.  
Confirme que su vehículo tlene un sistema eléctrico a tierra  
negativo de 13.2 (12) voltios.  
Confirme que está usando sólo el cordón provisto para la  
batería del automóvil. El uso de otro cordón puede dañar su  
TV/VCR.  
Asegúrese que no haya cenizas ni otro restos en el zócalo del  
encendedor.  
- 30 -  
ES  
0I29  
 
3) Seleccione “ENGLISH” o “ESPAÑOL” utilizando el  
botón F.FWD/B o REW/s. “[ ]” indica el idioma  
seleccionado.  
4) Pulse el botón PLAY/K o STOP/L para señalar  
“AUTOPRESELECCION”.  
Luego pulse el botón F.FWD/B. El sintonizador explo-  
rará y memorizará todos los canales activos de su área.  
NOTAS:  
Asegúrese de introducir completamente el enchufe del cordón de  
la batería del automóvil en el zócalo del encendedor de cigarril-  
los.  
Siempre desenchufe primero del zócalo del encendedor de ciga-  
rrillos el cordón para la batería del coche, antes de desconectar-  
lo de la TV/VCR.  
Antes de usar la alimentación de CA, usted debe desconectar de  
la TV/VCR el cordón para la batería del atuomóvil.  
Solamente reemplace un fusible por otro del mismo tipo 5A,  
250V.  
El televisor/videograbadora distingue entre los canales  
de televisión estándar y los canales de televisor por  
cable.  
Al zócalo del encendedor  
de cigarrillos el cordón  
para la batería del coche  
Si desea reproducir o grabar una cinta ANTES de prea-  
justar el sintonizador, usted tendrá que pulsar el botón  
MENU en el mando a distancia. Para preajustar de  
nuevo el sintonizador, consulte “REPETICIÓN DE LA  
PREPARACIÓN DE CANALES”.  
Antena de VHF/UHF  
para TV móvil  
(no incluído)  
La unidad de televisor/videograbadora puede reconocer  
los canales de TV como ellos de TV por cable a causa  
de los condiciones de recepción. En este caso, pruebe el  
preajuste automático de nuevo en los condiciones finas  
de recepción.  
Cordón para la batería  
del automóvil  
5) El sintonizador se para en el canal memorizado más  
bajo. Si desea recuperar canales seleccionados, usted  
podrá seleccionar directamente el canal deseado con los  
botones numerados del mando a distancia o con los  
botones CHANNEL K o L.  
DC 13.2V  
AC 120V  
DC13.2V  
ANT.  
ANT.  
MODO DE ENTRADA EXTERNA  
AJUSTE DEL RELOJ  
Cuando utilice una señal de entrada externa (otra  
videograbadora o una videocámara), conecte los cables de  
salida de audio/vídeo del equipo de reproducción a las  
tomas AUDIO IN/VIDEO IN de su  
televisor/videograbadora. Y luego pulse el botón CHAN-  
NEL K o L hasta que “AUX” aparezca en la pantalla.  
Cerciórese...  
La alimentación del televisor/videograbadora deberá  
estar conectada.  
En el ejemplo de abajo, el reloj va a ajustarse así:  
FECHA: 1 de mayo de 2001  
HORA: 5:40 PM  
Usted puede programar el temporizador para que explore  
todos los canales que puedan recibirse en su zona.  
1) Pulse el botón MENU en el mando a distancia.  
Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE RELOJ”.  
Luego, pulse el botón F.FWD/B.  
2) Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE MANUAL RELOJ”.  
Luego, pulse el botón F.FWD/B.  
3) Pulse el botón PLAY/K o STOP/L hasta que aparezca  
el mes deseado. (Ejemplo: Mayo - 05)  
Luego, pulse el botón F.FWD/B.  
4) Pulse el botón PLAY/K o STOP/L hasta que aparezca  
el día del mes deseado. (Ejemplo: 1 - 01)  
INSTALACIÓN DE LAS PILAS  
1)Abra la tapa del compartimiento de las pilas del mando  
a distancia presionándola en el sentido de la flecha.  
2)Inserte 2 pilas tamaño “AA” en el compartimiento de las  
pilas, en el sentido indicado por las marcas de polaridad  
(+/-).  
3)Vuelva a poner la tapa.  
Luego, pulse el botón F.FWD/B.  
5) Pulse el botón PLAY/K o STOP/L hasta que aparezca  
el año deseado. (Ejemplo: 2001)  
Luego, pulse el botón F.FWD/B.  
6) Pulse el botón PLAY/K o STOP/L hasta que aparezca  
la hora deseada. (Ejemplo: 5, PM)  
Luego, pulse el botón F.FWD/B.  
7) Pulse el botón PLAY/K o STOP/L hasta que aparezca  
el minuto deseado. (Ejemplo: 40)  
8) Pulse el botón MENU en el mando a distancia. Aunque  
los segundos no se visualizan, éstos empiezan a contar  
desde 00 cuando se pulsa MENU en el mando a distan-  
cia. Utilice esta función para sincronizar el reloj con la  
hora correcta.  
PREPARACIÓN DE CANALES POR  
PRIMERA VEZ  
1) Enchufe el cable de alimentación del  
televisor/videograbadora en una toma de CA estándar.  
NOTA: Si aparezcan algunos digitos en el rincón de la  
pantalla, pulse el botón POWER sin desenchufar el cable  
de alimentación.  
2) Pulse el botón POWER para encender el  
televisor/videograbadora.  
- 31 -  
ES  
 

Sharp Projector XR 40X User Manual
Shure Microphone 545L User Manual
Sony Ericsson Bluetooth Headset HBH 608 User Manual
Sony Network Card MSAC PC3 User Manual
Sony Portable Radio ICF 1000L User Manual
Sony Universal Remote RM AV2500T User Manual
Sun Microsystems Computer Hardware CP2500 User Manual
Sunrise Medical Mobility Aid Quickie S 525 User Manual
SVA Security Camera CRR 1103 User Manual
Swann Security Camera SW244 X6C User Manual