Belkin Power Supply F6U600AU User Manual

Line Interactive 600VA UPS  
Quick Install Guide  
F6U600au  
 
3 - Charging  
This unit is shipped from the factory with its internal battery fully charged, however  
some charge may be lost during shipping and the battery should be recharged prior to  
use. Plug the unit into an appropriate power outlet and allow the UPS to charge fully  
by leaving it plugged in for at least 6 hours with no load (no electrical devices such as  
computers, monitors, etc) connected.  
6 Hours  
4 - Computer Connection  
Connect your PC, monitor and modem/router into the outlets at the back of the  
UPS labelled "Battery Backup". Battery power is automatically provided in case  
of power failure.  
3
 
5 - Peripheral Equipment Connection  
Plug your peripheral equipment (printer, scanner or speakers) into the full-time surge  
protection outlet.  
This receptacle does not provide any power during a power failure.  
Printer  
Note: DO NOT plug a laser printer, copier, space heater, vacuum or other large electrical device into  
the UPS. The power demands of these devices will overload and possibly damage the unit.  
6 - Modem/Phone line Connection  
Plug incoming phone line into the "IN" socket on the front of the UPS. Connect another  
phone line cable into the "OUT" socket on the front of the UPS. Plug the other end into  
the modem input socket as shown.  
Incoming  
phone line  
Modem  
4
 
7 - Turn On/Off  
Press power switch to turn on the UPS. Press power switch again to turn off the UPS.  
8 - DC Start Function  
DC Start Function enables UPS to be started up when AC utility power is not available  
and battery is fully charged. Just simply press the power switch to turn on the UPS  
5
 
Installing Belkin Automatic Power  
Management Software  
Step 1:  
PC Installation  
- Insert CD  
Mac Installation  
- Insert CD  
- After a short moment  
the CD will automatically  
run  
- Open “Belkin APMS” CD icon  
- Open Mac OSX folder  
- Open Disk 1 folder  
- Open INSTDATA folder  
- Select setup icon  
Follow prompts until software is installed (Note: Mac users will be prompted to restart at  
the end of this process, do so)  
Upon completion you will now have an “agent’ icon in your system tray  
(PC) or in your dock (Mac).  
6
 
Installing Belkin Automatic Power  
Management Software  
Step 2:  
To launch the software,  
PC - double click agent icon in your system tray to start the monitor  
Mac - click the agent icon in your dock and select “Start Monitor”  
Step 3:  
Select System Menu then “Auto Search UPS”, the software should now detect your  
connected UPS.  
Step 4:  
Using the menu system on the left hand side of the software drill down levels until you  
reach the “LINE INT” level, you should receive a visual depiction of the operating UPS  
and general information about it’s status.  
Please consult the help menu in the software to configure advanced software features  
7
 
Important Safety Instructions  
Caution  
Please read the following information carefully and save this manual for future reference.  
Disregard of these safety notes may endanger life or health, as well as the function of the  
equipment and the safety of your data.  
Do not connect this product to another battery backup, power board, surge  
protector, extension cord or double adapter.  
Risk of Electric Shock. Heatsinks are live. Disconnect unit before servicing.  
Risk of Electric Shock. This unit receives power from more than one source.  
Disconnection of AC sources and the DC source is required to de-energise this unit  
before servicing.  
Risk of Electric Shock. Hazardous live parts inside this unit are energised from the  
battery supply even when the power cord is connected.  
Risk of Electric Shock. Do not remove cover. No user serviceable parts inside.  
Refer servicing to qualified service personnel.  
The sum of the leakage current of the UPS and the connected equipment should  
not exceed 3.5mA.  
Do not dispose of batteries in a fire as they may explode.  
Do not open or damage the battery. Released electrolyte is harmful to the skin and  
eyes. It may be toxic.  
A battery can present a risk of electric shock and high short circuit current.  
The following precaution should be observed when working on batteries:  
- Remove watches, rings or other metal objects from the handles  
- Use tools with insulated handles  
- Wear rubber gloves and boots  
- Do not lay tools or metal parts on top of the batteries  
- Disconnect charging source prior to connecting or disconnecting  
batteries terminal.  
The maximum ambient temperature rating is 40oC  
8
 
Specification  
Model  
F6U600au  
600VA/360W  
220/230/240VAC  
50/60Hz  
Capacity  
VA/W  
Voltage  
Input  
Frequency  
Phase  
Single  
Voltage Range  
Frequency  
Waveform  
Typical  
220/230/240VAC+10%  
50Hz or 60Hz+1Hz  
Modified Sinwave  
2-6ms  
Output  
(inverter Mode)  
Transfer Time  
Battery Type  
12V7Ahx1  
Backup Time at a PC  
load with monitor  
(Typical 100W)  
16-18 Minutes  
Battery  
6 hours max  
(recharge up to 90% capacity)  
Recharging Time  
Display  
LED  
Battery Mode  
Low Battery  
Overload  
Fault  
Power on, Backup, Fault  
Sounding every 10 seconds  
Sounding every second  
Sounding every 0.5 second  
Continuously Sounding  
Audible Alarm  
Overload, Modem/Phone  
Line Surge Protection and Short Circuit  
Protection  
Protection  
Physical  
Full Protection  
Dimension  
(DxWxH)  
330x100x140 (mm)  
Net Weight  
5.2kgs  
4 outlets (1 for surge protection, 3 for  
surge protection with battery backup)  
Outlets  
IEC  
Operation  
Temperature  
o
0-40 C  
Environment  
Interface  
Operation Humidity  
0-90%  
Supports Windows 98/2000/ME/XP/  
Vista/7 x32 and x64, Mac OS 10.x, Linux  
USB Port  
9
 
System Description  
Front  
1 Power Switch  
2 LCD indicators  
AC Mode: Green Lighting  
Battery Mode: Green Flashing  
Back  
1 Battery Backup & Surge Outlets  
2 Input & Fuse Inlet  
3 Modem/Phone Line Surge Protection  
4 USB Port  
5 Surge Protection Outlet  
10  
 
Troubleshooting  
If the UPS failed to operate properly, please review the following points first.  
Symptom  
Possible Cause  
Remedy  
LED is flashing  
and audible  
alarm is heard  
intermittently.  
UPS is not  
connected  
properly to  
the mains.  
Connect the UPS  
according to the  
installation guide.  
UPS is functioning  
but audible alarm is  
heard continuously.  
Overload of  
the UPS.  
Verify that the load  
matches the UPS  
capacity stated in  
the specifications.  
Communication lost  
between UPS and  
computer.  
Cable is not  
properly connected.  
Check if the USB  
cable is firmly  
connected to the  
USB port of the  
computer and  
confirm the setting.  
© 2011 Belkin International, Inc. All rights reserved. All  
trade names are registered trademarks of respective  
manufacturers listed.  
Belkin Ltd.  
4 Pioneer Avenue  
Tuggerah NSW 2259  
Australia  
Tel: 02 4350 4600  
Fax: 02 4350 4700  
8820-00941  
11  
 

Black Decker Cordless Saw 609747 26 User Manual
Black Decker Juicer CJ600 User Manual
Blue Rhino Outdoor Fireplace WAD794SP User Manual
Bradley Smoker Plumbing Product 232 007 User Manual
Canon Copier 0700 iC2200 25M User Manual
Canon Scanner DR 4080U User Manual
Casio Clock Radio MA0906 EA User Manual
Celestron Telescope 91517 User Manual
Chicago Electric Power Hammer 40457 User Manual
Chrysler Automobile 200 User Manual