Black Box Switch 4 x 1 and 8 x 1 VGA Switches with Audio User Manual

AVSW-VGA4X1A  
AVSW-VGA8X1A  
4 x 1 and 8 x 1 VGA Switches with Audio  
Share a VGA display output (monitor, projector,  
or TV) between multiple device VGA inputs.  
Both models have serial and 3.5-mm audio.  
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)  
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax  
724-746-0746 • Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence,  
PA 15055-1018 • Web site: www.blackbox.com • E-mail: [email protected]  
Customer  
Support  
Information  
 
NOM Statement  
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la  
tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.  
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean  
recomendados por el fabricante.  
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea  
recomendado por el fabricante.  
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá  
lo descrito en las instrucciones de operación. Todo otro servicio deberá ser  
referido a personal de servicio calificado.  
9. El aparato eléctrico debe ser situado de tal manera que su posición no  
interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,  
alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en  
libreros o gabinetes que impidan el flujo de aire por los orificios de ventilación.  
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como  
radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores)  
que producen calor.  
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo  
descrito en el instructivo de operación, o como se indique en el aparato.  
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del  
equipo no sea eliminada.  
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean  
pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo  
particular atención a los contactos y receptáculos donde salen del aparato.  
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las  
recomendaciones del fabricante.  
15. En caso de existir, una antena externa deberá ser localizada lejos de las  
lineas de energia.  
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado  
por un largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean  
derramados sobre la cubierta u orificios de ventilación.  
Page 3  
724-746-5500 | blackbox.com  
 
NOM Statement  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o  
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un cambio en su  
desempeño; o  
E: El aparato ha sido tirado o su cubierta ha sido dañada.  
Page 4  
724-746-5500 | blackbox.com  
 
Trademarks Used in this Manual  
Trademarks Used in this Manual  
Black Box and the Double Diamond logo are registered trademarks  
of BB Technologies, Inc.  
Xbox is a registered trademark of Microsoft Corporation.  
Wii is a registered trademark of Nintendo of America, Inc.  
Any other trademarks mentioned in this manual are acknowledged to be  
the property of the trademark owners.  
Page 5  
724-746-5500 | blackbox.com  
 
Table of Contents  
Table of Contents  
1. Specifications ............................................................................................. 7  
2. Overview  
............................................................................................. 8  
2.1 Introduction....................................................................................... 8  
2.2 Features............................................................................................. 8  
2.3 What’s Included................................................................................. 8  
2.4 Hardware Description........................................................................ 9  
2.4.1 AVSW-VGA4X1A Front and Back Panels............................... 9  
2.4.2 AVSW-VGA8X1A Front and Back Panels..............................11  
3. Installation  
............................................................................................13  
3.1  
Connection Pattern...........................................................................13  
3.2 Installation Steps...............................................................................14  
4. Operation (AVSW-VGA4X1A)......................................................................15  
4.1  
Front-Panel Indicators and Push Buttons...........................................15  
4.2 IR Remote Control ............................................................................15  
4.3 Serial Control....................................................................................16  
5. Operation (AVSW-VGA8X1A)......................................................................18  
5.1  
Front-Panel Indicators and Push Buttons...........................................18  
5.2 EDID Copy ........................................................................................19  
5.3 Remote Control ................................................................................19  
6. Troubleshooting ......................................................................................... 22  
6.1  
Contacting Black Box....................................................................... 22  
6.2 Shipping and Packaging .................................................................. 22  
Page 6  
724-746-5500 | blackbox.com  
 
Chapter 1: Specifications  
1. Specifications  
Maximum Video Resolution — 1920 x 1080, WUXGA (1920 x 1200)  
Number of A/V Inputs — Video: AVSW-VGA4X1A: (4);  
AVSW-VGA8X1A: (8);  
Audio: AVSW-VGA4X1A: (4);  
AVSW-VGA8X1A: (8)  
Number of A/V Outputs — Video: (1);  
Audio: (1)  
Remote Control Support — Yes  
Serial Control Support — Yes  
Enclosure — Metal  
User Controls — AVSW-VGA4X1A: (4) push buttons;  
AVSW-VGA8X1A: (4) push buttons, (1) “S” button, (1) EDID copy button,  
Connectors — AVSW-VGA4X1A: Input: (4) VGA female, (4) audio jacks;  
Output: (1) VGA female, (1) audio jack, (1) 2.5-mm RS-232 serial;  
AVSW-VGA8X1A: Input: (8) VGA female, (8) audio jacks;  
Output: (1) VGA female, (1) audio jack, (1) 2.5-mm RS-232 serial  
Indicators — AVSW-VGA4X1A: (5) LEDs: (1) Power (green), (4) Video input  
(yellow);  
AVSW-VGA8X1A: (9) LEDs: (1) Power (green and yellow), (8) Video input  
(yellow)  
Power Consumption (Maximum) — 4.5 W  
Size — 1.3"H x 8.7"W x 3.9"D (3.4 x 22 x 10 cm)  
Weight — 1.5 lb. (0.7 kg)  
Page 7  
724-746-5500 | blackbox.com  
 
Chapter 2: Overview  
2. Overview  
2.1 Introduction  
The 4- and 8-Port VGA Switches enable users to quickly and easily share a single  
VGA display with several sources from your device inputs to one output device  
(monitor, projector, or TV). You can select the desired input source via the remote  
control within the range of 15 feet (5 m) or by using a push button on the switch.  
Because you don’t need to plug and unplug video sources, it’s more convenient,  
more affordable, and more efficient to use your A/V equipment.  
The built-in serial interface on the AVSW-VGA4X1A and AVSW-VGA8X1A also  
enables users to control the unit via an RS-232/serial device.  
2.2 Features  
• Switch between (4) or (8) sources.  
• Switch audio and video.  
• Use front-panel buttons for easy switching.  
• Supports IR remote control.  
• Supports serial remote control.  
• LEDs show the status of input video and audio.  
• Supports VGA monitors at resolutions up to 1920 x 1200.  
2.3 What’s Included  
Your package should contain the following items. If anything is missing  
or damaged, contact Black Box Technical Support at 724-746-5500  
AVSW-VGA4X1A:  
• 4 x 1 VGA/Audio Switch  
• Universal power supply with power cord  
• IR remote control  
• Serial cable (DB9 F to 2.5-mm plug)  
• 19" rackmount kit wth mounting hardware  
• (1) set of foot pads  
• Screw pack  
• This user’s manual  
Page 8  
724-746-5500 | blackbox.com  
 
Chapter 2: Overview  
AVSW-VGA8X1A:  
• 8 x 1 VGA Video Switch with Audio  
• Universal power supply with power cord  
• IR remote control  
• Serial cable (DB9 F to 2.5-mm plug)  
• 19" rackmount kit wth mounting hardware  
• (1) set of foot pads  
• Screw pack  
• This user’s manual  
For both models, you might also need:  
• Audio cable (EJ110)  
• 6-ft. (1.8-m) VGA Cable (M-to-M) for VGA A/V source connection (EVNPS06).  
2.4 Hardware Description  
2.4.1 AVSW-VGA4X1A Front and Back Panels  
Figure 2-1 shows the front panel of the AVSW-VGA4X1A. Figure 2-2 shows the  
back panel. Table 2-1 describes its components.  
1
4
3
2
Figure 2-1. AVSW-VGA4X1A front panel.  
Page 9  
724-746-5500 | blackbox.com  
 
Chapter 2: Overview  
5 6  
7
8
9
10  
Figure 2-2. AVSW-VGA4X1A back panel.  
Table 2-1. AVSW-VGA4X1A components.  
Number  
Component  
Description  
1
LEDs  
Lights when the corresponding input is selected.  
2
Push buttons  
LED  
Press to select input 1, 2, 3, or 4.  
Lights when power is on.  
3
4
Sensor  
IR sensor accepts remote control signal.  
Connects to power.  
5
Barrel connector  
DCE  
6
2.5-mm serial control port.  
Links to audio out.  
7
3.5-mm connector  
3.5-mm connectors  
VGA connector  
VGA connectors  
8
Link to audio inputs 1, 2, 3, and 4.  
Connects to VGA output.  
9
10  
Connects to VGA inputs 1, 2, 3, and 4.  
Page 10  
724-746-5500 | blackbox.com  
 
Chapter 2: Overview  
2.4.2 AVSW-VGA8X1A Front and Back Panels  
Figure 2-3 shows the front panel of the AVSW-VGA8X1A. Figure 2-4 shows the  
back panel. Table 2-2 describes its components.  
2
5
3 4  
1
Figure 2-3. AVSW-VGA8X1A front panel.  
10  
6 7 8  
9
11  
12  
Figure 2-4. AVSW-VGA8X1 back panel.  
Page 11  
724-746-5500 | blackbox.com  
 
Chapter 2: Overview  
Table 2-2. AVSW-VGA8X1A components.  
Number Component  
Description  
1
2
3
LEDs  
Lights when the corresponding input is selected.  
Push buttons  
LED  
Press to select input 1, 2, 3, 4.  
Lights when power is on.  
Press and hold the “S” button, then press the “K1” button to select Port 5.  
Press and hold the “S” button, then press the “K2” button to select Port 6.  
Press and hold the “S” button, then press the “K3” button to select Port 7.  
Press and hold the “S” button, then press the “K4” button to select Port 8.  
IR sensor accepts remote control signal.  
4
S button  
5
Sensor  
6
Barrel connector  
DCE  
Connects to power.  
7
2.5-mm serial control port.  
8
3.5-mm connector  
EDID copy button  
VGA connectors  
VGA connector  
Links to audio out.  
9
Connects the monitor to the switch so that the switch can copy the EDID.  
Connects to VGA inputs 1, 2, 3, 4, 5, 6, 7, 8.  
Connects to VGA output.  
10  
11  
12  
3.5-mm connectors Link to audio inputs 1, 2, 3, 4, 5, 6, 7, and 8.  
Page 12  
724-746-5500 | blackbox.com  
 
Chapter 3: Installation  
3. Installation  
Before installation, power off all devices that will be connected to this system.  
Make sure that all devices you will connect are properly grounded.  
Place cables away from fluorescent lights, air conditioners, and machines that are  
likely to generate electrical noise.  
NOTE: If no screen displays, follow these steps:  
1. Make sure the device cables are correctly and firmly attached.  
2. Set your display device’s input source as VGA.  
3. Check the PC BIOS configuration for the video output settings.  
4. Connect your computer to the display DIRECTLY to check if the video signal  
gets through.  
3.1 Connection Pattern  
Figure 3-1 shows a typical connection of the 4 x 1 VGA Switch with Serial and  
3.5-mm Audio.  
4
1
3
3
2
3
3
Figure 3-1. AVSW-VGA4X1A connection.  
Page 13  
724-746-5500 | blackbox.com  
 
Chapter 3: Installation  
Table 3-1. Connection pattern, AVSW-VGA4X1A.  
Number  
Component  
Description  
1
Power supply  
Apply the proper power to the unit.  
2
3
4
Video output  
Connects to the display.  
Video source (input)  
Serial connector  
Connects to the video source.  
Plug the serial cable in here.  
3.2 Installation Steps  
1. Use a video cable (VGA) to connect the display to the video output port on the  
back of the switch. Plug a set of audio jacks from the speaker to the switch’s  
speaker port.  
2. Use a video cable (VGA) to connect the source device to the video input port  
on the switch. Use an audio cable to connect the speaker port from the input  
side of the unit to the corresponding output port on the source device.  
3. Plug the power supply into the switch and power on the switch.  
4. Turn on the display (monitor, projector, or TV) and then power on the source  
device(s).  
NOTE: For both AVSW-VGA4X1A and AVSW-VGA8X1A, each video source is  
powered on, make sure it has a display pointing to it for EDID  
communication. If a source does not have a display pointing to it, a video  
image might not display.  
Page 14  
724-746-5500 | blackbox.com  
 
Chapter 4: Operation (AVSW-VGA4X1A)  
4. Operation (AVSW-VGA4X1A)  
4.1 Front-Panel Indicators and Push Buttons  
Figure 4-1. AVSW-VGA4X1A.  
Table 4-1. Front-panel indicators.  
Product Code  
Indicator  
Power LED  
Description  
Lights green when the video switch is powered on.  
AVSW-VGA4X1A  
Video Port LEDs 1–4 Lights yellow when the corresponding video port is selected.  
Table 4-2. Front-panel push buttons.  
Product Code  
Push Buttons  
Description  
AVSW-VGA4X1A  
(4) Video source  
Press the corresponding button to select Ports 1–4.  
4.2 IR Remote Control  
Using the included remote control, users can control the switch within a range of  
15 feet (5 m). To select a source device with a remote control, press the  
number button (1–4 or 1–8, depending on the model) to directly switch to the  
corresponding port.  
NOTE: Remove the “battery protector” on the remote control before operation.  
NOTE: On the remote control, only Buttons 1–4 are activated.  
Page 15  
724-746-5500 | blackbox.com  
 
Chapter 4: Operation (AVSW-VGA4X1A)  
Figure 4-2. Remote control.  
4.3 Serial Control  
The video switch’s built-in serial interface allows users to control the switch  
through a PC, serial controller devices, or home theater systems.  
Configure the controller’s serial port as shown below:  
Baud Rate: 9600  
Data Bits: 8  
Parity: None  
Stop Bits: 1  
Flow Control: None  
Page 16  
724-746-5500 | blackbox.com  
 
Chapter 4: Operation (AVSW-VGA4X1A)  
To select a source device via serial interface, select the number that corresponds to  
the port it is connected to (see Figure 4-3).  
Figure 4-3. Serial interface screen.  
NOTE: Use a DB9F-to-2.5-mm cable for the serial connection.  
Page 17  
724-746-5500 | blackbox.com  
 
Chapter 5: Operation (AVSW-VGA8X1A)  
5. Operation (AVSW-VGA8X1A)  
5.1 Front-Panel Indicators and Push Buttons  
To select Source Ports 1–4, simply press the corresponding front-panel button  
(K1–K4) on the switch.  
To select Source Port 5, press and hold the “S” button on the switch, then press  
K1 to select Port 5.  
To select Source Port 6, press and hold the “S” button on the switch, then press  
K2 to select Port 6.  
To select Source Port 7, press and hold the “S” button on the switch, then press  
K3 to select Port 7.  
To select Source Port 8, press and hold the “S” button on the switch, then press  
K4 to select Port 8.  
NOTE: Each port selection step should be individual.  
Table 5-1. Push button controls.  
Then press the  
“K1” key to  
select…  
Or press the  
“K2” key to  
select…  
Or press the  
“K3” key to  
select…  
Start with this key  
sequence…  
Or press the “K4”  
key to select…  
None  
Source 1  
Source 2  
Source 3  
Source 4  
Source 8  
Press hold the “S”  
key for more than 3 Source 5  
seconds.  
Source 6  
Source 7  
Table 5-2. Dual-color (green and red) LED next to S button.  
LED  
Mode  
LED Color  
LED State  
Turns green when  
the video switch is  
powered on.  
Green  
Next to “S” button  
Status  
Turns yellow  
when the port  
is selected.  
Yellow  
Page 18  
724-746-5500 | blackbox.com  
 
Chapter 5: Operation (AVSW-VGA8X1A)  
Table 5-3. Single-color (yellow) LEDs next to buttons 1–8.  
LED Number  
Color  
Yellow  
Yellow  
Yellow  
Yellow  
Yellow  
Yellow  
Yellow  
Yellow  
Description  
1
2
3
4
5
6
7
8
The video port on Source 1 is selected.  
The video port on Source 2 is selected.  
The video port on Source 3 is selected.  
The video port on Source 4 is selected.  
The video port on Source 5 is selected.  
The video port on Source 6 is selected.  
The video port on Source 7 is selected.  
The video port on Source 8 is selected.  
5.2 EDID Copy  
STEP 1: Power on the unit.  
STEP 2: Connect the EDID compliant monitor to the switch and power on the  
monitor.  
STEP 3: Press the “EDID COPY” button for 3–5 seconds, and release the button  
RIGHT AFTER the Power LED flashes green.  
STEP 4: The Power LED flashes yellow and green alternately then lights green  
indicating the copy is successful.  
NOTE: If the Power LED flashes yellow, the reason could be:  
1. The monitor is not connected.  
2. The monitor is not powered on.  
3. The EDID data of the monitor is not applicable.  
5.3 Remote Control  
Using the included remote control, users can control the switch within a range of  
15 feet (5 m). To select a source device with a remote control, press the  
button number (1–8), to directly switch to the corresponding port.  
NOTE: Remove the “battery protector” on the remote control before operation.  
NOTE: On the remote control, Buttons 1–8 are activated.  
Page 19  
724-746-5500 | blackbox.com  
 
Chapter 5: Operation (AVSW-VGA8X1A)  
Figure 5-1. Remote control.  
Page 20  
724-746-5500 | blackbox.com  
 
Chapter 6: Troubleshooting  
6. Troubleshooting  
6.1 Contacting Black Box  
If you determine that your VGA switch is malfunctioning, do not attempt to alter  
or repair the unit. It contains no user-serviceable parts. Contact Black Box  
Technical Support at 724-746-5500 or [email protected].  
Before you do, make a record of the history of the problem. We will be able to  
provide more efficient and accurate assistance if you have a complete description,  
including:  
• the nature and duration of the problem.  
• when the problem occurs.  
• the components involved in the problem.  
• any particular application that, when used, appears to create the problem or  
make it worse.  
6.2 Shipping and Packaging  
If you need to transport or ship your VGA switch:  
• Package it carefully. We recommend that you use the original container.  
• If you are returning the unit, make sure you include everything you received  
with it. Before you ship for return or repair, contact Black Box to get a Return  
Authorization (RA) number.  
Page 21  
724-746-5500 | blackbox.com  
 
NOTES  
Page 22  
724-746-5500 | blackbox.com  
 
NOTES  
Page 23  
724-746-5500 | blackbox.com  
 
Black Box Tech Support: FREE! Live. 24/7.  
Tech support the  
way it should be.  
Great tech support is just 30 seconds away at  
724-746-5500 or blackbox.com.  
About Black Box  
Black Box Network Services is your source for an extensive range of networking  
and infrastructure products. You’ll find everything from cabinets and racks and  
power and surge protection products to media converters and Ethernet switches  
all supported by free, live 24/7 Tech support available in 30 seconds or less.  
© Copyright 2012. Black Box Corporation. All rights reserved.  
AVSW-VGA4X1A, version 1  
724-746-5500 | blackbox.com  
 

Blanco Indoor Furnishings 513 689 User Manual
Bolens Lawn Mower 111 330A User Manual
Bolens Snow Blower 191 967 A User Manual
Bosch Appliances Home Security System DVA 16K User Manual
Bosch Appliances Smoke Alarm D720 User Manual
Bravetti Fryer EP67 User Manual
Breville Mixer BSB530 User Manual
Bryant Furnace 394HAD User Manual
Campbell Hausfeld Nail Gun CHN10401 User Manual
Cisco Systems Home Theater Server 4300G User Manual