Black Decker Impact Driver 90500690 User Manual

the item being measured. The arrow on the moving jaw points to a marker on the  
measurement scale. This point represents the size of the item being measured.  
NOTE: To measure in inches, use the standard scale located on the front of the wrench. To  
measure in millimeters, use the metric scale located on the backside of the wrench.  
Replacing the Batteries:  
TM  
• Using a phillips tip screwdriver, unscrew  
the battery compartment cover located on  
the backside of the wrench.  
AAW100 - AUTO WRENCH  
• Remove the battery compartment cover  
and replace the “AAA” batteries following  
the (+/-) polarity indicators in the battery  
compartment.  
INSTRUCTION MANUAL  
NOTE: For optimum performance, use alkaline batteries.  
• Replace the battery compartment cover and screw.  
Troubleshooting  
There are no user serviceable parts inside except for the batteries. Always insert batteries  
correctly with regard to polarity (+ and -), marked on the battery and the equipment.  
For assistance with your product, visit our website www.blackanddecker.com for the  
location of the service center nearest you or call the BLACK & DECKER help line at  
1-800-544-6986.  
Service Information  
All Black & Decker Service Centers are staffed with trained personnel to provide customers  
with efficient and reliable power tool service. Whether you need technical advice, repair, or  
genuine factory replacement parts, contact the Black & Decker location nearest you. To find  
your local service location, refer to the yellow page directory under "Tools—Electric" or call:  
Full Two-Year Home Use Warranty  
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in materia  
or workmanship. The defective product will be replaced or repaired at no charge in either of  
two ways.  
THANK YOU FOR CHOOSING BLACK & DECKER!  
GO TO WWW.BLACKANDDECKER.COM/NEWOWNER  
TO REGISTER YOUR NEW PRODUCT.  
The first, which will result in exchanges only, is to return the product to the retailer from  
whom it was purchased (provided that the store is a participating retailer). Returns should be  
made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after  
the sale). Proof of purchase may be required. Please check with the retailer for their specific  
return policy regarding returns that are beyond the time set for exchanges.  
The second option is to take or send the product (prepaid) to a Black & Decker owned or  
authorized Service Center for repair or replacement at our option. Proof of purchase may be  
required.Black & Decker owned and authorized Service Centers are listed under  
"Tools-Electric" in the yellow pages of the phone directory.  
BEFORE RETURNING THIS PRODUCT  
FO1R-A8NY0R0E-AS5O4N4PL-E6A9SE8C6ALL  
BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A  
BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU  
HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO  
BLACK & DECKER.  
This warranty does not apply to accessories. This warranty gives you specific legal rights  
and you may have other rights which vary from state to state or province to province. Should  
you have any questions, contact the manager of your nearest Black & Decker Service  
Center. This product is not intended for commercial use.  
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are  
missing, call 1-800-544-6986 for a free replacement.  
Imported by  
See ‘Tools-Electric’  
– Yellow Pages –  
for Service & Sales  
Black & Decker (U.S.) Inc.,  
701 E. Joppa Rd.  
Towson, MD 21286 U.S.A.  
SAVE THIS MANUAL FOR FUTURE REFERENCE.  
VEA EL ESPAÑOL EN LA CONTRAPORTADA.  
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.  
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.  
CLÉ À CRÉMAILLÈRE  
AUTO WRENCH AAW100  
Cat No. AAW100  
Form No. 90500690 (FEB. - 06) Copyright © 2006 Black & Decker Printed in China  
MERCI D’AVOIR CHOISI BLACK & DECKER!  
VISITEZ WWW.BLACKANDDECKER.COM/NEWOWNER  
POUR ENREGISTRER VOTRE NOUVEAU PRODUIT.  
WARNING: Read and understand all instructions. Failure to follow all instructions  
listed below may result in electric shock, fire and/or serious personal injury.  
WARNING: Fire or burn hazard. Batteries can explode, or leak, and can cause injury  
or fire. To reduce this risk:  
AVANT DE RETOURNER CE PRODUIT POUR QUELQUE  
RAISON QUE CE SOIT, COMPOSER LE NUMÉRO  
SUIVANT : 1 800 544-6986  
• Carefully follow all instructions and warnings on the battery label and package.  
• Always insert batteries correctly with regard to polarity (+ and -), marked on the battery  
and the equipment.  
• Do not short battery terminals.  
• Do not recharge.  
• Remove dead batteries immediately and dispose of per local codes.  
• Do not dispose of batteries in fire.  
AVERTISSEMENT : lire et comprendre toutes les directives. Négliger de suivre toute  
les directives de sécurité figurant ci-après peut entraîner un choc électrique, un incendie  
et/ou des blessures corporelles.  
• Keep batteries out of reach of children.  
• Remove batteries if the device will not be used for several months.  
"Transporting batteries can possibly cause fires if the battery terminals inadvertently  
come in contact with conductive materials such as keys, coins, hand tools and the like.  
The US Department of Transportation Hazardous Material Regulations (HMR) actually  
prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and  
carryon luggage) UNLESS they are properly protected from short circuits. So when  
transporting individual batteries, make sure that the battery terminals are protected and  
well insulated from materials that could contact them and cause a short circuit."  
AVERTISSEMENT : risque d’incendie ou de brûlures. Les piles peuvent exploser  
ou couler et causer des blessures ou un incendie. Pour réduire ce risque :  
• Suivre attentivement toutes les directives et avertissements figurant sur l’étiquette des  
piles et de l’emballage de l’appareil.  
Toujours insérer les piles selon la polarité correcte (+ et -), comme indiqué sur les piles et  
le matériel.  
• Ne pas créer de court-circuit dans les bornes des piles.  
• Ne pas recharger.  
• Retirer immédiatement les piles déchargées et les éliminer en fonction de la  
réglementation locale en vigueur.  
IMPORTANT:  
• Do NOT use the wrench as a hammer.  
• Ne pas jeter les piles dans un feu.  
• Do NOT use extensions on the wrench to increase torque.  
• Garder les piles hors de la portée des enfants.  
• Retirer les piles si l’appareil n’est pas utilisé pendant plusieurs mois.  
« Le transport des piles peut provoquer un incendie si les bornes des piles entrent en  
contact involontairement avec des matières conductrices comme des clés, de la mon-  
naie, des outils manuels et d’autres éléments semblables. La Hazardous Material  
Regulation du département américain des transports interdit en fait le transport des  
piles pour le commerce ou dans les avions (par ex. : piles emballées dans des valises  
et des bagages à main) À MOINS qu’elles soient bien protégées contre les courts-cir-  
cuits. Pour le transport de piles individuelles, s’assurer que les bornes sont protégées  
et bien isolées contre toute matière pouvant entrer en contact avec elles et causer un  
court-circuit. »  
One Touch Operation Toggle Switch  
FEATURES:  
IMNPe POARSTutAilisNeTr la:clé comme marteau.  
Built-in Measurement Scale  
Hang Tab  
• Ne PAS utiliser de rallonges avec la clé pour augmenter le couple.  
CARACTÉRISTIQUES :  
OPERATING THE AUTO WRENCHTM  
Interrupteur à bascule qui fonctionne avec un  
simple touché  
WARNING: Always use proper eye protection.  
• Open the Auto Wrench’s TM jaw by pressing the bottom end of the toggle switch located on  
the handle.  
• Position the wrench’s jaw around the item to be loosened, tightened or measured.  
• Then press and hold down the top end of the toggle switch until the wrench’s jaw closes  
around it and release the button. NOTE: Auto WrenchTM will stay locked in position until  
otherwise adjusted.  
To manually adjust the size of the opening use the thumb wheel to open and close the jaws.  
USING THE MEASUREMENT SCALE:  
Auto WrenchTM comes with a built-in measurement scale (standard and metric) to measure  
nuts, bolts, pipes, hose fittings and more.  
Échelle de mesure intégrée  
Onglet de suspension  
To Measure:  
• Open Auto Wrench’sTM jaw by pressing the bottom end of the toggle switch.  
• Position the wrench jaw around the item to be measured.  
• Press and hold down the top end of the toggle switch until the wrench jaw closes around  
 

Belkin Computer Drive F5U140 User Manual
Beyerdynamic Headphones 459038 User Manual
Billion Electric Company Network Router 7202G User Manual
Black Decker Bread Maker B2005 User Manual
Broan Ventilation Hood RP2 User Manual
Broan Ventilation Hood WC26I User Manual
Bushnell Digital Camera 119405 User Manual
Chamberlain Garage Door Opener MR650EVO User Manual
Christie Digital Systems Projector DCP H User Manual
Cisco Systems IP Phone OL 4314 01 User Manual