Bosch Appliances Flat Panel Television MON150CL User Manual

15-inch Color LCD Flat Panel Display Monitor  
Instruction Manual  
EN MON150CL  
 
|
MON150CL | Instruction Manual | Safety Precautions  
EN 3  
Safety Precautions  
For Indoor Product  
1. Water and Moisture - Do not use this unit near  
water - for example, in a wet basement, in an  
unprotected outdoor installation or in any area  
classified as a wet location.  
CAUTION: TO REDUCE THE RISK OF  
2. Object and Liquid Entry - Never push objects of  
any kind into this unit through openings, as they  
might touch dangerous voltage points or create  
short circuits, resulting in a fire or electrical  
shock. Never spill liquid of any kind on the unit.  
3. Power Cord and Power Cord Protection - For  
units intended to operate with 230VAC, 50Hz,  
the input and output power cord must comply  
with the latest versions of IEC Publication 227 or  
IEC Publication 245.  
ELECTRIC SHOCK, DO NOT REMOVE COVER  
(OR BACK). NO USER SERVICEABLE PARTS  
INSIDE. REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
This symbol indicates the presence of  
uninsulated “dangerous voltage” within the  
product’s enclosure that can cause an electric  
shock.  
This symbol indicates the presence of  
important operating and maintenance  
(servicing) instructions in the literature  
accompanying the appliance.  
Power supply cords should be routed so they are  
not likely to be walked on or pinched. Pay  
particular attention to location of cords and plugs,  
convenience receptacles, and the point of exit  
from the appliance.  
Installation should be performed by qualified  
service personnel only in accordance with the  
National Electrical Code or applicable local  
codes.  
4. Overloading - Do not overload outlets and  
extension cords; this can result in a risk of fire or  
electrical shock.  
Power Disconnect. Units with or without  
ON-OFF switches have power supplied to the  
unit whenever the power cord is inserted into the  
power source; however, the unit is operational  
only when the ON-OFF switch is in the ON  
position. The power cord is the main power  
disconnect for all units.  
For Outdoor Product  
Power Lines - An outdoor system should not be  
located in the vicinity of overhead power lines,  
electric lights or power circuits, or where it may  
contact such power lines or circuits. When  
installing an outdoor system, extreme care should  
be taken to keep from touching power lines or  
circuits, as this contact might be fatal. U.S.A.  
models only - refer to the National Electrical  
Code Article 820 regarding installation of CATV  
systems.  
Cover Removal  
WARNING: Removal of the cover should only be  
performed by qualified service personnel - not user  
serviceable. The unit should always be unplugged before  
removing the cover and remain unplugged while the  
cover is removed.  
For Rack-mount Product  
1. Ventilation - Do not place this equipment in a  
built-in installation or rack, unless proper  
ventilation is provided, or the manufacturer's  
instructions were followed. The equipment must  
not exceed its maximum operating temperature  
requirements.  
2. Mechanical Loading - When rack-mounting the  
equipment, ensure that a hazardous condition is  
not created by uneven mechanical loading.  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual | FCC & ICES Information  
EN 4  
FCC & ICES INFORMATION  
(U.S.A. and Canadian Models Only)  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions:  
(1)  
(2)  
This device may not cause harmful interference, and  
This device must accept any interference received,  
including interference that may cause undesired  
operation.  
NOTE: This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to Part 15 of  
the FCC Rules and ICES-003 of Industry Canada. These limits  
are designed to provide reasonable protection against harmful  
interference when the equipment is operated in a residential  
installation. This equipment generates, uses and can radiate radio  
frequency energy, and if not installed and used in accordance  
with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference  
will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or  
more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
• Consult the dealer, or an experienced radio/TV technician for  
help.  
Intentional or unintentional changes or modifications, not  
expressly approved by the party responsible for compliance, shall  
not be made. Any such changes or modifications could void the  
user’s authority to operate the equipment.The user may find the  
following booklet, prepared by the Federal Communications  
Commission, helpful: How to Identify and Resolve Radio-TV  
Interference Problems. This booklet is available from the U.S.  
Government Printing Office, Washington, DC 20402,  
Stock No. 004-000-00345-4.  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual | Contents  
EN 5  
Table of Contents  
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Front and Back Panel Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
1.0  
1.1  
2.0  
3.0  
3.1  
4.0  
4.1  
5.0  
5.1  
5.2  
5.3  
5.4  
5.5  
5.6  
5.7  
6.0  
6.1  
6.2  
7.0  
7.1  
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
GENERAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Desktop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8  
Connecting the Composite Video Signal to the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8  
Connecting the Y/C (S-video) Signal to the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8  
Connecting Audio to the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8  
Connecting the Analog VGA Signal to the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
On-screen Display (OSD) Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
ON-SCREEN DISPLAY MENU CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
CVBS Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
VGA Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12  
7.2  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual | Front Panel  
EN 6  
MON150CL  
Key:  
A. AUTO (Input)Button  
B. +, - Buttons  
C. MENU Button  
D. Power LED Identification  
E. Power Button  
A
B
C D  
E
Figure 1: Front Panel  
A
B
C
D
E
A. DC input  
B. VGA input  
C. Video(CVBS) input  
D. Y/C input  
E. Audio input  
Figure 2: I/O Connectors  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual | Unpacking  
EN 7  
1.0 UNPACKING  
3.0 GENERAL FEATURES  
This high-performance, 15-inch TFT LCD monitor  
with a 1024 X 768 XGA resolution has been designed  
to display both PC and Video images. It complies with  
the power management regulations of VESA DPMS, it  
is supported by Plug & Play, and complies with  
DDC1/2B.  
This equipment should be unpacked and handled with  
care. If an item appears to have been damaged in  
shipment, notify the shipper.  
Verify that all parts shown in the Parts List have been  
included. If any items are missing, notify your Bosch  
Security Systems Sales or Customer Service  
Representative.  
3.1 Features  
100 to 240 VAC Power Supply  
NTSC/PAL Auto - Detect  
High Resolution (1024 X 768 XGA)  
PC Input  
The original packing carton is the safest container in  
which to transport the unit. Save it for possible future use.  
1.1 Parts List  
Qty Item  
Video Input  
1
1
2
Unit (verify model number)  
Audio Input  
MON150CL Color LCD Flat Panel Monitor  
Y/C Input  
Power Cords: 3-wire with grounded plug, 1.8 m (6 ft)  
long; One (1) with European Continental plug type and  
one (1) with U.S plug type  
OSD with Multiple Languages  
1
1
1
1
1
MON150PS power supply  
One (1) analog VGA cable, 1.5 m (5 ft)  
One (1) audio cable  
4.0 INTRODUCTION  
4.1 Monitors  
RCA to BNC connector  
This installation manual  
The MON150CL 15-inch (38 cm) Color Liquid Crystal  
Display Monitor displays PAL or NTSC standard color  
pictures in CCTV systems. The MON150CL monitor  
includes one (1) Composite Video input RCA  
connector (one RCA to BNC connector is included),  
one (1) Audio input mini phone jack, and one (1) Y/C  
(S-video) input using 4-pin mini-DIN. In addition, this  
model includes an Analog VGA input using 15-pin  
D-sub to accommodate the increasing use of Personal  
Computers and digital video devices in security  
applications. Monitor control functions are accessed  
via the front panel push buttons and the multi-  
language On-Screen Display (OSD).  
2.0 SERVICE  
If the unit needs servicing, contact the nearest Bosch  
Security Systems Service Center for authorization to  
return and shipping instructions.  
Service Centers  
USA  
Phone:  
Fax:  
800-366-2283 or 717-735-6638  
800-366-1329 or 717-735-6639  
CCTV Spare Parts  
Phone:  
Fax:  
800-894-5215 or 408-956-3853 or 3854  
408-957-3198  
5.0 INSTALLATION  
E-mail:  
Canada  
Phone:  
5.1 Power  
514-738-2434  
Model  
No.  
Rated  
Voltage  
Range  
Power  
Sync  
Europe, Middle East & Asia Pacific Region  
Phone: 32-1-440-0711  
Voltage  
at Rated Format  
Voltage  
For additional information, see  
MON150CL 120/230 VAC 100 to 240 V 26 W  
NTSC/PAL  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual | Installation  
EN 8  
5.2 Desktop Installation  
The MON150CL monitor is delivered with a 3-pole  
US-style power cord and a 3-pole Euro-style power  
cord. Use the US-style power cord where 120 VAC,  
60 Hz power is available; and use the Euro-style  
power cord where 230 VAC, 50 Hz power is available.  
Connect the bayonet connector from the power supply  
to the power input connector on the rear side of the  
LCD panel, as shown in Photo A. The monitor  
automatically adjusts to either power input voltage.  
Photo C  
5.4 Connecting the Y/C (S-video) Signal  
to the Monitor  
There is one (1) mini-DIN type connector for the  
S-video (Y/C) input (please see Figure 2 on Page 6 and  
Figure 3 below).  
NOTE: Both Y and C inputs are terminated with 75.  
3
4
1. GND  
2. GND  
3. Y-signal IN  
4. C-signal IN  
Photo A  
2
1
5.3 Connecting the Composite Video  
Signal to the Monitor  
There is one (1) RCA connector located on the rear of  
the monitor for composite video input (please see  
Figure 2 on Page 6). Also included is one (1) RCA to  
BNC adapter used to connect a BNC cable line as  
shown in Photo B and Photo C.  
Figure 3: Y/C Connection Pinout  
5.5 Connecting Audio to the Monitor  
There is one (1) set of mini phone jacks for the audio  
connector (please see Figure 2 on Page 6 and Photo D  
below).  
Photo D  
Photo B  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual | Operation  
EN 9  
5.6 Connecting the Analog VGA Signal  
to the Monitor  
Contrast  
Adjusts the contrast value  
(0-100)  
There is one (1) 15-pin D-sub connector (Figure 4) for one  
analog VGA input. Refer to Figure 2, item B.  
Brightness Adjusts the brightness value  
(0-100)  
Tint  
Adjusts the tint value (NTSC only)  
(0-100)  
Saturation Adjusts the color value  
(0-100)  
Figure 4: Analog VGA Connector  
Volume  
Exit  
Adjusts the volume  
(0-31)  
5.7 Ventilation  
To prevent overheating, ensure that the ventilation  
openings on the rear of the monitor are not covered.  
Exits the OSD menu  
6.2.2 Colour Setting (RGB / VGA)  
Colour Setting  
6.0 OPERATION  
6.1  
Front Panel Controls (Figure 1)  
1. Press Menu to open the OSD Main menu  
AUTO (Input)  
+/-  
Press this button to display the input  
signal which is selected on the screen  
2. Press the ‘+’ or ‘-’ button to highlight an option,  
then press Menu to modify the value of the option  
Press the ‘+’ or ‘-’ button to move the  
cursor to the targeted parameter in the  
OSD main menu. Press the ‘+’ or ‘-’  
button to adjust the value of the selected  
parameter in the OSD sub-menu.  
MENU  
Press this button to open the main OSD  
menu. Use this button to confirm a value  
for a parameter in the OSD Menu.  
Power LED  
Identification  
Power on (Green)  
Stand by (Amber)  
Contrast  
Adjusts the contrast value  
(0-100)  
POWER  
Press this button to turn on or turn off  
the monitor  
Brightness Adjusts the brightness value  
(0-100)  
6.2 On-screen Display (OSD) Menu  
Gamma Correct  
6.2.1 Video Setting (CVBS/S-VIDEO)  
Opens an optimum Gamma curve  
(0/1/2/3)  
Saturation  
1. Press Menu to open the OSD Main menu  
Colour Adjust  
Opens the color menu. Select a color  
then press Menu to adjust the value of  
the selected color.  
2. Press the ‘+’ or ‘-’ button to highlight an option,  
then press Menu to modify the value of the option  
Exit  
Exits the Colour OSD menu setting  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual | Operation  
EN 10  
6.2.5  
OSD Menu (CVBS/S-VIDEO / RGB / VGA)  
6.2.3  
Picture Setting (RGB / VGA)  
Language Opens the Language Selection Menu  
Select one of the following: English,  
Deutsch, Francais, Italiano, Espanol,  
Simple Chinese, Traditional Chinese,  
Japanese  
H Position Adjusts the horizontal position  
(0-100)  
V Position Adjusts the vertical position  
(0-100)  
OSD  
H. Position  
Adjusts the OSD horizontal position  
(0-100)  
Sharpness Adjusts the sharpness value  
(1/2/3/4/5)  
OSD  
V. Position  
Adjusts the OSD vertical position  
(0-100)  
Phase  
Clock  
Exit  
Adjusts the phase value  
(0-31)  
OSD Time Adjusts the OSD window display time  
Adjusts the clock frequency  
(0-200)  
(0-30)  
Translucent Toggles the OSD window background  
Exits the Picture OSD Menu setting  
setting  
6.2.4  
Auto Function Setting (RGB / VGA)  
Exit  
6.2.6  
Exits the OSD menu setting  
Miscellaneous (CVBS/S-VIDEO / RGB / VGA)  
Auto Adjust Automatically adjusts the H/V  
position, phase, and clock  
Signal Source  
Prompts you to select an input source  
Auto Position Automatically adjusts the H/V position  
Auto Phase Automatically adjusts the phase  
Mode Select  
Prompts you to select one of these  
modes: 640 X 400 or 720 X 400  
Auto Clock Automatically adjusts the clock  
frequency  
Reset  
Exit  
Returns the monitor setting to the  
factory default  
Auto Colour Automatically adjusts the color  
temperature  
Exit  
Exits the Function OSD Menu setting  
Exits the Miscellaneous menu setting  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual | On-Screen Display Menu Configuration  
EN 11  
7.0 ON - SCREEN DISPLAY MENU  
CONFIGURATION  
7.1  
CVBS Mode  
CVBS  
Video Setting  
Contrast  
Brightness  
Tint  
Color  
Volume  
Exit  
OSD Menu  
Language  
English  
Deutsch  
Francais  
Italiano  
Espanol  
Simple Chinese  
Traditional Chinese  
Japanese  
OSD H. Position  
OSD V. Position  
OSD Timer  
Translucent  
Exit  
On  
Off  
On  
Off  
D-Sub  
CVBS  
Miscellaneous  
Signal Source  
S-Video  
Mode Select  
Reset  
Yes  
No  
Exit  
Exit  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual | On-Screen Display Menu Configuration  
EN 12  
7.2  
VGA Mode  
RGB (VGA)  
Colour  
Contrast  
Brightness  
Gamma Correct  
Colour Adjust  
Exit  
Red  
Green  
Blue  
Exit  
Picture  
H. Position  
V. Position  
Sharpness  
Phase  
Clock  
Exit  
Yes  
No  
Function  
Auto Adjust  
Auto Position  
Auto Phase  
Auto Clock  
Auto Colour  
Exit  
Yes  
No  
Yes  
No  
Yes  
No  
Yes  
No  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual | On-Screen Display Menu Configuration  
EN 13  
OSD Menu  
Language  
English  
Deutsch  
Francais  
Italiano  
Espanol  
Simple Chinese  
Traditional Chinese  
Japanese  
OSD H. Position  
OSD V. Position  
OSD Timer  
Translucent  
Exit  
On  
Off  
On  
Off  
D-Sub  
CVBS  
S-Video  
Miscellaneous  
Signal Source  
Mode Select  
Reset  
Yes  
No  
Exit  
Exit  
Error Message: Signal Out of Range  
This message appears in VGA  
7.2.1 Supported Resolutions  
VGA Timing Modes  
mode if the PC is operating with a  
resolution or timing mode that is  
not supported by the MON150CL.  
Please change the PC settings to  
one of the supported VGA Timing  
Mode combinations listed.  
640 x 480  
800 x 600  
1024 x 768  
60/72/75 Hz  
60/72/75 Hz  
50/60/70/75 Hz  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual |  
EN 14  
Bosch Security Systems | May 20, 2005  
 
|
MON150CL | Instruction Manual |  
EN 15  
Bosch Security Systems | May 20, 2005  
 
Americas  
Bosch Security Systems  
130 Perinton Parkway  
Fairport, New York, 14450, USA  
Phone: +1 (585) 223 4060  
+1 800 289 0096  
Europe, Middle East, Africa  
Bosch Security Systems B.V.  
P.O. Box 80002  
5600 JB Eindhoven, The Netherlands  
Phone: +31 (0) 40 27 83955  
Asia-Pacific  
Bosch Security Systems Pte Ltd  
38C Jalan Pemimpin  
Singapore 577180  
Phone: +65 6319 3450  
Fax:  
+31 (0) 40 27 86668  
Fax:  
+65 6319 3499  
© 2005 Bosch Security Systems GmbH  
F01U009193_01 05-20 | Updated May 20, 2005 | Data subject to change without notice.  
 

Bissell Vacuum Cleaner 33N8 User Manual
Black Decker Blender BL10451G User Manual
Black Decker Trimmer ST4500YK User Manual
Bolens Lawn Mower 5264D User Manual
Brother Printer HL 1260 User Manual
Bushnell Binoculars SCOUT1000 User Manual
Calphalon Toaster 1779206 User Manual
Cannon Electric Pressure Cooker C60DT User Manual
Canon Camera Lens 9321A002 User Manual
Chicago Electric Automobile Battery Charger 95000 User Manual