Bosch Appliances Security Camera NDC 274 P User Manual

MicroDome Camera 200 Series  
NDC-274-P, NDC-274-PT, NDC-284-PT, NDC-274-PM  
en Installation Manual  
 
MicroDome Camera 200 Series  
Table of Contents | en  
3
Table of Contents  
Safety  
Safety precautions  
Important safety instructions  
FCC & ICES compliance  
UL certification  
Bosch notices  
Copyrights  
Introduction  
Features  
Unpacking  
Installation  
Disassembly  
Memory card  
Desiccant for rugged cameras  
Network (and power) connector  
Power connection  
DC power connection  
Mounting  
Camera set-up  
Camera positioning  
Resetting the camera  
Closing the unit  
Browser connection  
Protected network  
Troubleshooting  
Resolving problems  
Customer service  
Maintenance  
Repairs  
Transfer and disposal  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
4
en | Table of Contents  
MicroDome Camera 200 Series  
Technical Data  
Specifications  
Accessories  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
MicroDome Camera 200 Series  
Safety | en  
5
1
Safety  
1.1  
Safety precautions  
DANGER!  
High risk: This symbol indicates an imminently hazardous  
situation such as "Dangerous Voltage" inside the product.  
If not avoided, this will result in an electrical shock, serious  
bodily injury, or death.  
WARNING!  
Medium risk: Indicates a potentially hazardous situation.  
If not avoided, this could result in minor or moderate bodily  
injury.  
CAUTION!  
Low risk: Indicates a potentially hazardous situation.  
If not avoided, this could result in property damage or risk of  
damage to the device.  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
   
6
en | Safety  
MicroDome Camera 200 Series  
1.2  
Important safety instructions  
Read, follow, and retain for future reference all of the following  
safety instructions. Heed all warnings on the unit and in the  
operating instructions before operating the unit.  
1. Cleaning - Generally, using a dry cloth for cleaning is  
sufficient but a moist, fluff-free cloth or leather shammy  
may also be used. Do not use liquid cleaners or aerosol  
cleaners.  
2. Heat Sources - Do not install the unit near any heat  
sources such as radiators, heaters, stoves, or other  
equipment (including amplifiers) that produce heat.  
3. Water - Never spill liquid of any kind on the unit.  
4. Lightning - Take precautions to protect the unit from  
power and lightning surges.  
5. Controls adjustment - Adjust only those controls specified  
in the operating instructions. Improper adjustment of  
other controls may cause damage to the unit.  
6. Power sources - Operate the unit only from the type of  
power source indicated on the label.  
7. Servicing - Unless qualified, do not attempt to service this  
unit yourself. Refer all servicing to qualified service  
personnel.  
8. Replacement parts - Use only replacement parts specified  
by the manufacturer.  
9. Installation - Install in accordance with the manufacturer's  
instructions and in accordance with applicable local codes.  
10. Attachments, changes or modifications - Only use  
attachments/accessories specified by the manufacturer.  
Any change or modification of the equipment, not  
expressly approved by Bosch, could void the warranty or,  
in the case of an authorization agreement, authority to  
operate the equipment.  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
 
MicroDome Camera 200 Series  
Safety | en  
7
1.3  
FCC & ICES compliance  
FCC & ICES Information  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to part 15 of the  
FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following  
measures:  
reorient or relocate the receiving antenna;  
increase the separation between the equipment and  
receiver;  
connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected;  
consult the dealer or an experienced radio/TV technician  
for help.  
This device complies with part 15 of the FCC Rules. Operation  
is subject to the following two conditions:  
1. this device may not cause harmful interference, and  
2. this device must accept any interference received,  
including interference that may cause undesired operation.  
Intentional or unintentional modifications, not expressly  
approved by the party responsible for compliance, shall not be  
made. Any such modifications could void the user's authority to  
operate the equipment. If necessary, the user should consult  
the dealer or an experienced radio/television technician for  
corrective action.  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
 
8
en | Safety  
MicroDome Camera 200 Series  
The user may find the following booklet, prepared by the  
Federal Communications Commission, helpful: How to Identify  
and Resolve Radio-TV Interference Problems. This booklet is  
available from the U.S. Government Printing Office,  
Washington, DC 20402, Stock No. 004-000-00345-4.  
1.4  
UL certification  
Disclaimer  
Underwriter Laboratories Inc. ("UL") has not tested the  
performance or reliability of the security or signaling aspects of  
this product. UL has only tested fire, shock and/or casualty  
hazards as outlined in UL's Standard(s) for Safety for Closed  
Circuit Television Equipment, UL 2044. UL Certification does not  
cover the performance or reliability of the security or signaling  
aspects of this product.  
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR  
CERTIFICATIONS WHATSOEVER REGARDING THE  
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR  
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.  
1.5  
Bosch notices  
Disposal - Your Bosch product was developed and  
manufactured with high-quality material and components that  
can be recycled and reused. This symbol means that  
electronic and electrical appliances, which have reached the  
end of their working life, must be collected and disposed of  
separately from household waste material. Separate collecting  
systems are usually in place for disused electronic and  
electrical products. Please dispose of these devices at an  
environmentally compatible recycling facility, per European  
Directive 2002/96/EC  
More information  
For more information please contact the nearest Bosch Security  
Systems location or visit www.boschsecurity.com  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
   
MicroDome Camera 200 Series  
Safety | en  
9
1.6  
Copyrights  
The firmware 4.1 uses the fonts "Adobe-Helvetica-Bold-R-  
Normal--24-240-75-75-P-138-ISO10646-1" and "Adobe-  
Helvetica-Bold-R-Normal--12-120-75-75-P-70-ISO10646-1"under  
the following copyright:  
Copyright 1984-1989, 1994 Adobe Systems Incorporated.  
Copyright 1988, 1994 Digital Equipment Corporation.  
Permission to use, copy, modify, distribute and sell this  
software and its documentation for any purpose and without  
fee is hereby granted, provided that the above copyright  
notices appear in all copies and that both those copyright  
notices and this permission notice appear in supporting  
documentation, and that the names of Adobe Systems and  
Digital Equipment Corporation not be used in advertising or  
publicity pertaining to distribution of the software without  
specific, written prior permission.  
This software is based in part on the work of the Independent  
JPEG Group.  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
 
10 en | Introduction  
MicroDome Camera 200 Series  
2
Introduction  
2.1  
Features  
This MicroDome camera is a ready-to-use, complete network  
video surveillance system inside a compact camera. The camera  
offers a cost-effective solution for a broad range of  
applications. It uses H.264 compression technology to give  
clear images reducing bandwidth and storage.The camera can  
be used as a stand-alone video surveillance system with no  
additional equipment or it can easily integrate with the Bosch  
DVR 700 Series recorders.  
Features include:  
MicroSD/SDHC/SDXC card slot supports edge recording  
up to 2 TB  
Tri-streaming: Two H.264 streams and one M-JPEG stream  
Progressive scan for sharp images of moving objects  
Built-in microphone (NDC-274-P only)  
Tamper, motion and audio detection  
Conforms to the ONVIF standard for wide compatibility  
Power over Ethernet (IEEE 802.3af compliant)  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
   
MicroDome Camera 200 Series  
Introduction | en 11  
2.2  
Unpacking  
Unpack carefully and handle the equipment with care.  
The packaging contains:  
IP camera with lens  
Installation paper sticker  
Quick installation guide  
Torx screwdriver for dome cover  
Optical disk  
Bosch Video Client  
Documentation  
Tools  
If equipment has been damaged during shipment, repack it in  
the original packaging and notify the shipping agent or supplier.  
WARNING!  
Installation should only be performed by qualified service  
personnel in accordance with the National Electrical Code or  
applicable local codes.  
CAUTION!  
The camera module is a sensitive device and must be handled  
carefully.  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
 
12 en | Installation  
MicroDome Camera 200 Series  
3
Installation  
3.1  
Disassembly  
The camera/housing unit consists of the following parts:  
x3  
Dome  
Camera module and mounting base  
To disassemble the unit proceed as follows:  
1. Using the special screwdriver bit supplied, loosen the  
three tamper-resistant screws in the dome (the screws  
remain in place).  
2. Remove the dome from the base.  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
   
MicroDome Camera 200 Series  
Installation | en 13  
3.2  
Memory card  
Figure 3.1 Memory card  
1. Disassemble the camera.  
2. Slide the microSD card into the slot.  
The camera supports most microSD/SDHC/SDXC cards.  
Note:  
Use high speed SD cards, class 6 or above (the higher read/  
write speed the better).  
3.3  
Desiccant for rugged cameras  
Figure 3.2 Desiccant for PT and PM camera versions.  
1. Remove backing from desiccant package.  
2. Stick the package to the inside of the dome cover as  
indicated.  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
   
14 en | Installation  
MicroDome Camera 200 Series  
3.4  
Network (and power) connector  
RJ45  
M12  
Ethernet (PoE)  
Ethernet (PoE)  
Figure 3.3 Network connection  
Connect the camera to a 10/100 Base-T network.  
Use a shielded UTP Category 5e cable with RJ45  
connectors (M12 connector for PM version).  
Power can be supplied to the camera via the Ethernet  
cable compliant with the Power-over-Ethernet  
(IEEE 802.3af) standard.  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
 
MicroDome Camera 200 Series  
Installation | en 15  
3.5  
Power connection  
The camera can accept power from both the DC12/24V power  
input and the Ethernet input at the same time. (Changing the  
power source might lead to a camera reboot.)  
3.5.1  
DC power connection  
(Not present on NDC-274-PM version.)  
5 mm  
(0.2 in)  
22AWG  
12 VDC  
24 VDC  
Figure 3.4 DC power connection  
1. Slide the plug adapter that matches your outlet socket  
onto the supplied power supply.  
2. Insert the power connector jack from the power supply  
into the DC12/24V socket of the camera.  
3. Connect the power supply to either a 230 VAC or a  
120 VAC power supply outlet.  
Note:  
A power supply is not included in the package.  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
   
16 en | Installation  
MicroDome Camera 200 Series  
3.6  
Mounting  
0~  
FRONT  
Inner 2.5mm  
2
Holes  
(M3 TYPE SCREW)  
270°  
90°  
Outer  
6.0mm 2 Holes  
(FOR PLASTIC ANCHOR)  
x2  
CABLE  
mm  
6
CAMERA  
OUTLINE  
CUT LINE  
Ø
180°  
M3 (Ø2.5 mm)  
x2  
Figure 3.5 Mounting the camera  
To mount the camera to a wall or ceiling:  
1. Stick the supplied installation paper sticker to the surface  
taking care to orientate it correctly.  
2. Drill two holes with a diameter of 6 mm.  
3. Insert the supplied plugs into the holes.  
4. Attach the camera and base unit securly to the surface  
using the two supplied M3 screws.  
CAUTION!  
Do not point the camera/lens into direct sunlight as this may  
damage the sensors.  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
 
MicroDome Camera 200 Series  
Installation | en 17  
3.7  
Camera set-up  
To help set up the camera, connect a monitor to the miniature  
2.5 mm jack socket using a S1460 monitor cable which can be  
ordered separately. This monitor jack socket provides a  
composite video signal (NTSC) for installation purposes only.  
S1460 Monitor Cable  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
 
18 en | Installation  
MicroDome Camera 200 Series  
3.7.1  
Camera positioning  
The camera module position can be adjusted along two axes.  
When adjusting the camera position ensure that the picture  
display on the monitor is level.  
CAUTION!  
The image sensors are highly sensitive and require special care  
for proper performance and extended lifetime. Do not expose  
them to direct sunlight or bright spotlights in operating and  
non-operating conditions. Avoid bright lights in the field of view  
of the camera.  
Set the camera to the desired position by performing the  
following steps:  
1. For horizontal adjustment (pan) rotate the camera module  
in the base. Do not rotate more than 350°.  
2. For vertical adjustment (tilt) rotate camera. Do not rotate  
more than 55°.  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
 
MicroDome Camera 200 Series  
Installation | en 19  
3.8  
Resetting the camera  
If the camera cannot be connected because the IP address has  
changed, press and hold the reset button (7 seconds  
approximately) to recall the factory default values. The factory  
default IP address is 192.168.0.1  
Figure 3.6 Reset button  
3.9  
Closing the unit  
When the camera position is set and all adjustments have been  
made, close the unit.  
1. Remove the monitor cable from the jack socket.  
2. If necessary, clean the inner surface of the dome with a  
soft cloth.  
3. Position the dome on the base by aligning the two screw  
holders with fins with the openings beside the screw  
sockets and slot it home.  
4. Use the supplied special screwdriver bit to tighten the  
three tamper-resistant screws.  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
   
20 en | Browser connection  
MicroDome Camera 200 Series  
4
Browser connection  
A computer with Microsoft Internet Explorer can be used to  
receive live images from the camera, control the camera, and  
replay stored sequences. The camera is configured over the  
network using the browser.  
Note:  
The camera can also be configured using the supplied Bosch  
Video Client or the Bosch Video Management System.  
4.1  
Protected network  
If a RADIUS server is used for network access control (802.1x  
authentication), the camera must be configured first. To  
configure the camera for a Radius network, connect it directly  
to a PC via a crossed network cable and configure the two  
parameters, Identity and Password. Only after these have been  
configured can communication with the camera via the network  
occur.  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
   
MicroDome Camera 200 Series  
Troubleshooting | en 21  
5
Troubleshooting  
5.1  
Resolving problems  
The following table is intended to help identify the causes of  
malfunctions and correct them when possible.  
Malfunction  
Possible causes  
Solution  
No image  
Faulty cable connections. Check all cables, plugs,  
transmission to  
remote location.  
contacts and  
connections.  
No connection  
The unit's configuration.  
Faulty installation.  
Check all configuration  
parameters.  
established, no  
image transmission.  
Check all cables, plugs,  
contacts and  
connections.  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
   
22 en | Troubleshooting  
MicroDome Camera 200 Series  
5.2  
Customer service  
If a fault cannot be resolved, please contact your supplier or  
system integrator, or contact Bosch Security Systems  
Customer Service directly.  
The Installer should write down all information regarding the  
unit so that it can be referenced for warranty or repair. The  
version numbers of the firmware and other status information  
can be seen when the unit starts or by opening the Service  
menu. Note down this information and the information found  
on the camera label before contacting customer service.  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
 
MicroDome Camera 200 Series  
Maintenance | en 23  
6
Maintenance  
6.1  
Repairs  
CAUTION!  
Never open the casing of the camera. The unit does not contain  
any user serviceable parts. Ensure that all maintenance or  
repair work is performed only by qualified personnel (electrical  
engineering or network technology specialists). If in doubt,  
contact your dealer's technical service center.  
6.1.1  
Transfer and disposal  
The camera should only be passed-on together with this  
installation guide. The unit contains environmentally hazardous  
materials that must be disposed of according to law. Defective  
or superfluous devices and parts should be disposed of  
professionally or taken to your local collection point for  
hazardous materials.  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
     
24 en | Technical Data  
MicroDome Camera 200 Series  
7
Technical Data  
7.1  
Specifications  
Input voltage  
+12 VDC, +24 VDC, or Power-over-Ethernet  
Power consumption  
Sensor type  
3.84 W (max)  
1/2.7-inch CMOS  
1/3.2-inch CMOS (NDC-284-PT)  
Sensor pixels  
1920 x 1080  
2592 x 1944 (NDC-284-PT)  
Sensitivity  
0.3 lx  
Video resolution  
1080p, 720p, 480p, 240p  
5 Megapixels, 480p (NDC-284-PT)  
Video compression  
Max. frame rate  
H.264 MP (Main Profile);  
M-JPEG  
30 fps  
12 fps (NDC-284-PT)  
(M-JPEG frame rate can vary depending on  
system loading)  
Lens type  
4.37 mm fixed, F2.0  
3.74 mm fixed, F2.0 (NDC-284-PT)  
Audio Input  
Built-in microphone (NDC-274-P only)  
G.711, L16 (live and recording)  
Audio compression  
Analogue video out  
2.5 mm jack for installation only (NTSC)  
(not for NDC-274-PM)  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
   
MicroDome Camera 200 Series  
Technical Data | en 25  
Memory card slot  
Supports up to 32 GB microSDHC / 2 TB  
microSDXC card  
(An SD card of Class 6 or higher is recommended  
for HD recording)  
Recording  
Continuous recording, ring recording. alarm/  
events/schedule recording  
Unit Configuration  
Protocols  
Via web browser or PC surveillance software  
IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP,  
IGMPV2/V3, ICMP, RTSP, FTP, Telnet, ARP, DHCP,  
SNTP,SNMP (V1, MIB-II), 802.1x, SMTP, iSCSI,  
UPnP(SSDP)  
Encryption  
TLS 1.0, SSL  
Ethernet  
10/100 Base-T, auto-sensing, half/full duplex  
Ethernet connector  
RJ45  
M12 D-coded female (NDC-274-PM)  
PoE  
IEEE 802.3af compliant  
Dimensions  
(NDC-274-P)  
Diameter: 105 mm (4.13 in)  
Height: 56 mm (2.2 in)  
Weight  
255 g (8.99 oz) approx.  
(NDC-274-P)  
Dimensions  
Diameter: 110 mm (4.33 in)  
Height: 55 mm (2.17 in)  
Weight  
330 g (11.64 oz) approx.  
IP protection  
Impact protection  
IP66 (PT and PM versions only)  
IK08 (PT and PM versions only)  
-20 ºC to +50 ºC (-4 ºF to +122 ºF)  
Operating  
Temperature  
Bosch Security Systems  
Installation Manual  
AR18-10-B012 | v1.55 | 2012.09  
 
26 en | Technical Data  
MicroDome Camera 200 Series  
Storage  
-20 ºC to +70 ºC (-4 ºF to +158 ºF)  
Temperature  
Humidity  
10% to 80% relative humidity (non-condensing)  
7.1.1  
Accessories  
Contact a Bosch representative in your area for the latest  
available accessories or visit our website at  
AR18-10-B012 | v1.55 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
 
 
Bosch Security Systems  
© Bosch Security Systems, 2012  
 

Black Box Modem RF115 User Manual
Black Decker Rice Cooker RC1800 User Manual
Bosch Appliances Medical Alarms SE8830S304 User Manual
Brunton Camping Equipment 81 100695~225 User Manual
Bush Hog Brush Cutter RMB1445 User Manual
Bushnell Binoculars 11 8322G User Manual
Cambridge Audio Stereo Amplifier Azur 840W User Manual
Carrier Blower 58SSB User Manual
Casio Musical Toy Instrument CGP700 User Manual
Cateye Bicycle Accessories HL RC220 User Manual