Campbell Hausfeld Home Theater System NS2190 User Manual

Instruction Sheet  
Models NS3490 and NS2190  
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.  
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury, death  
and/or property damage! Retain instructions for future reference.  
Notes  
Notes  
Notas  
Framing Nailer  
BUILT TO LAST  
Note: This framing nailer is shipped  
with the BLACK single cycle mode  
trigger installed.  
Each time the Work Contact Element is  
depressed, a nail is driven into the  
work surface. Extreme care should be  
taken because a nail will be driven  
when the WCE is pressed against any  
surface.  
Always know the  
!
WARNING  
operational  
mode of the nailer before using.  
Failure to know the operational  
mode could result in death or seri-  
ous personal injury.  
Since the tool can be actuated without  
removing the finger from the trigger,  
this is considered to be a less restrictive  
mode, suitable for more experienced  
users.  
Operational Modes  
This stick framing nailer may be operat-  
ed in the “Single Cycle” or the “Bottom  
Trip” mode. The nailer is delivered in  
the single cycle mode. A separate ‘red’  
trigger for “Bottom Trip” mode is  
included with tool as an accessory.  
MODE CONVERSION  
To convert the tool from one mode to  
the other:  
1. Remove o-ring on the side of trig-  
ger pin.  
2. Remove trigger pin, trigger, and  
trigger spring.  
3. Switch out only the trigger.  
4. Replace trigger spring, trigger, trig-  
ger pin, and o-ring.  
ponents other than those intended for  
this tool.  
SINGLE CYCLE MODE  
When the black trigger is installed,  
nailer is in single cycle mode. This  
method is recommended when precise  
nail placement is required. Operation  
in this mode requires trigger to be  
pulled each time a nail is driven. Nailer  
can be actuated by depressing the  
Work Contact Element (WCE) against  
work surface followed by pulling the  
trigger.  
See the tool manual for further Safety  
and Operation information.  
Contact your Campbell Hausfeld repre-  
sentative if you have any questions.  
Do not attempt to modify the trigger  
components in any manner and do not  
attempt to use any other trigger com-  
Mode Conversion  
The trigger must be released after each  
fastener is driven to allow tool to reset.  
Trigger spring  
Since the tool can only be actuated by  
first removing the finger from the trig-  
ger, this is considered to be a more  
restrictive mode of operation, suitable  
for less experienced users.  
O-ring  
BOTTOM TRIP MODE  
When the red trigger is installed, the  
nailer is in bottom trip mode. This  
method is recommended when less  
precise nail placement is required.  
Operation in this mode requires trigger  
to be depressed with nailer off of the  
work surface. Then, the nose of the  
nailer is tapped against the work sur-  
face causing a nail to be driven.  
Trigger  
Trigger pin  
Campbell Hausfeld nailer meet or exceed Industries’ Standards as set forth by the American National  
Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.  
IN704300AV 8/05  
4
© 2005 Campbell Hausfeld  
For parts, product & service information  
 

Bionaire Air Cleaner BAP815 User Manual
BIXOLON Automobile Accessories TTGO129 ST RVC User Manual
Black Box Computer Hardware RM610A R2 User Manual
Black Box Network Hardware KV2008A User Manual
Black Decker Fan BDHF551 User Manual
Black Decker Kitchen Utensil FM1400 User Manual
Blanco Microwave Oven B 830FX User Manual
Bravo View Car Stereo System SD 100U User Manual
Canon Digital Camera SX410ISBLACK User Manual
Cardinal Gates Safety Gate EX 5 User Manual