Campbell Hausfeld Thermostat WT6000 User Manual

Instruction Manual  
Instructions D’Utilisation  
Manuel De Instrucciones  
Model WT6000  
Modéle WT6000  
Modelo WT6000  
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.  
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or  
property damage! Retain instructions for future reference.  
S’il vous plaît lire et conserver ces instructions. Lire attentivement avant de monter, installer, utiliser ou de procéder à l’entretien du produit  
décrit. Se protéger ainsi que les autres en observant toutes les instructions de sécurité, sinon, il y a risque de blessure et/ou dégâts matériels!  
Conserver ces instructions comme référence.  
Sírvase leer y guardar estas instrucciones. Lea con cuidado antes de tratar de armar, instalar, manejar o darle servicio al producto descrito en  
este manual. Protéjase Ud. y a los demás observando todas las reglas de seguridad. El no seguir las instrucciones podría resultar en heridas y/o  
daños a su propiedad. Guarde este manual como referencia.  
Mig Kit  
Nécessaire Mig  
TM  
Juego para soldar al estilo Mig  
BUILT TO LAST  
fitting on the rear of the welder and  
the other end to the fitting on the  
regulator using hose clamps on each  
connection. Make sure the gas hose is  
not kinked or twisted.  
place on your welding machine or other  
support to prevent the cylinder from falling  
over.  
General Safety  
!
DANGER  
Cylinders can explode if  
damaged. Shielding gas  
cylinders contain gas  
under high pressure.  
REGULATOR  
4. Once again, stand opposite the  
cylinder outlet and slowly open the  
cylinder valve. Inspect for leaks in the  
connections.  
5. This regulator is factory preset at  
30cfh. No adjustment is necessary.  
Also, a pop-out indicator in the end of  
the regulator shows the amount of  
gas left in the cylinder. When not  
extended, the cylinder is  
approximately 10 minutes away from  
empty.  
6. Remember to close the gas valve  
when finished welding.  
This regulator is designed to be used with  
straight Argon or Argon mix gas. A  
2
threaded adapter is needed if CO is used.  
An adapter is available at your local  
welding gas supplier to change between  
the two.  
Protect compressed gas cylinders from  
excessive heat, mechanical shocks, and  
arcs.  
Install and secure cylinders in an  
upright position by chaining them to  
stationary support or equipment  
cylinder rack to prevent falling or  
tipping.  
HOOKUP PROCEDURE  
Cylinder gas is  
!
WARNING  
under high  
pressure. Point cylinder outlet away  
from yourself and any bystanders  
before opening.  
Never allow a welding electrode to  
touch any cylinder.  
1. With the cylinder securely installed,  
remove the cylinder cap, stand to the  
side of the cylinder opposite the outlet,  
and open the valve slightly, turning  
counterclockwise. When gas is emitted  
from the cylinder, close the valve by  
turning clockwise. This will blow out  
dust or dirt that may have accumulated  
around the valve seat.  
Turn face away from valve outlet  
when opening cylinder valve.  
Keep protective cap in place over valve  
except when cylinder is in use or  
connected for use.  
Read and follow instructions on  
compressed gas cylinders, associated  
equipment, and CGA publication P-1.  
2. Install the gas regulator onto the gas  
cylinder and tighten the stem nut  
securely to the gas valve.  
Never use  
!
DANGER  
flammable gasses  
with MIG welders. Only inert or non-  
flammable gasses are suitable for  
MIG welding. Examples are carbon  
dioxide, argon, helium, or mixtures of  
one or more of these gasses.  
3. Install one end of the gas hose to the  
Argon or Argon Mix Installation  
Installation dArgon ou Mélange dArgon  
Never lift cylinders  
Installación para soldar con Argón o mezcla de Argón  
!
WARNING  
off the ground by  
Cap  
Chapeau  
Tapa  
Pop-out  
their valves, caps, or with chains or  
slings.  
indicator  
Indicateur sortant  
Indicador  
POLARITY  
For gas shielded welding, plug the cable  
coming out of the torch into the (+) socket  
and the ground clamp cable into the (-)  
socket on the welder.  
GAS TYPES  
2
CO Installation  
There are 3 types of gas generally used for  
gas metal arc welding; 100% argon, a  
mixture of 75% argon and 25% carbon  
2
Installation CO  
Instalación del CO  
2
25  
dioxide (C ) or 100% carbon dioxide. All can  
be used, but the 75/25 mixture is  
recommended for general welding. For  
aluminum welding, use 100% Argon. Either  
type gas may be obtained at your local  
welding supply outlet. Secure cylinder in  
2
CO Adapter  
2
Adaptateur CO  
Adaptador para CO  
2
Figure 1 Hookup Branchement Conexiones  
IN211300AV 8/01  
For parts, product & service information  
© 2001 Campbell Hausfeld  
 

Belkin Network Router PM01218ea F5D7634 4 User Manual
Belkin Switch F1U126 KIT User Manual
Bissell Vacuum Cleaner 12U9 User Manual
Black Decker Food Processor FP1611SCKT User Manual
Black Decker Network Card CA DHWK User Manual
Blue Rhino Charcoal Grill GBC900W C User Manual
Breville Rice Cooker BRC520 User Manual
Brother All in One Printer 2850 User Manual
Canon Camera Flash 133 D User Manual
Casio GPS Receiver E 200 User Manual