Chief Manufacturing Indoor Furnishings FSA 1017 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Pole Clamp Accessory  
Model: FSA-1017  
The FSA-1017 Pole Clamp Accessory is used to provide  
a means for attaching a desktop or wall mount to a  
1 1/2" to 2" pole.  
BEFORE YOU BEGIN  
CAUTION!  
To prevent damage to the Kit, which could affect or void the Factory warranty, and to the equipment that will be  
attached to it, thoroughly study all instructions and illustrations before you begin the installation.  
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480.  
8807-000042  
CHIEF MANUFACTURING INC.  
1-800-582-6480 952-894-6280 FAX 952-894-6918  
8401 EAGLE CREEK PARKWAY, STE 700  
SAVAGE, MINNESOTA 55378 USA  
©2005 Chief Manufacturing  
12/05  
 
Installation Instructions  
Model: FSA-1017  
NOTE: The following steps reuse hardware set aside  
10. Secure pole mount rear (20) to pole mount front (10)  
and pole by tightening three BHCS (20) using 5/32"  
hex key.  
during existing mount preparation.  
2. Place large Nylon washer into seat in pole mount  
front. (see Figure 4)  
3. Slide pivot pin through large nylon washer and down  
into pole mount front. (see Figure 4)  
Pole  
(30)  
Pole Mount front (10)  
with Swing Arm  
4. Slide swing arm assembly down onto top of pivot pin.  
5. Assemble two flat waskhers and one nylon washer  
onto button head cap screw. (see Figure 4)  
6. While holding Nylock nut, previously installed into  
pole mount front, slide button head cap screw with  
washers through swing arm and down into pole mount  
front until contact with Nylock nut is made.  
7. Secure swing arm to pole mount front by screwing  
button head cap screw into nylock nut.  
(20)  
NOTE: It may be necessary to move Nylock nut slighty  
in order to allow button head cap screw to  
properly seat in nut and allow tightening.  
Figure 5: Mount FSA-1017 with Swing Arm on Pole  
Phillips BHCS  
Flat Washer  
ADJUSTMENTS  
The FSA-1017 allows for both vertical and horizontal  
position adjustment on pole.  
To adjust FSA-1017 position:  
Swing Arm  
Nylon Washer  
Flat Washer  
1. Loosen single (right) rear BHCS (30). (see Figure 6)  
2. Move FSA-1017 to desired position. (see Figure 6)  
3. Tighten BHCS (30).  
CAUTION!  
ALWAYS use two people when adjusting FSA-1017  
position.  
Pivot Pin  
Adjustment Screw  
Large Nylon Washer  
Recessed Seat  
Pole Mount  
(Front)  
View From Rear  
Figure 4: Install Swing Arm to Front Pole Mount  
8. Place pole mount front with swing arm against pole in  
approximate mounting location.  
9. Place three BHCS (30) into pole mount rear (20) and  
place against pole aligning with mount front (10).  
Figure 6: Pole Mount Adjustment  
3
 
Model: FSA-1017  
Installation Instructions  
4
 

Belkin Computer Accessories F4D153 1 User Manual
Billion Electric Company Switch BiGuard 10 User Manual
Black Box Film Camera LMC213A MMSC User Manual
Bolens Lawn Mower LT 185 User Manual
Boston Acoustics Car Speaker Neo Type M SE User Manual
Bushnell Telescope 78 8831, 78 8846 User Manual
Cannon Electric Pressure Cooker 10250G User Manual
Casio Digital Camera EX Z 280 User Manual
Cecilware Griddle EL 1624T User Manual
Chamberlain Door 655501 User Manual