I N S T A LL A T I O N IN S T R U C T IO N S
MEDIUM FLAT PANEL DISPLAY STATIC MOUNT
MSR Series
The MSR Series static mount accommodates medium
flat panel displays weighing up to 125 lbs (57 kgs).
The teardrop holes in the mount allow for quick
connect/disconnect of the display, thus simplifying
installation and maintenance processes.
The top and bottom mounting brackets are adaptable to
single wood stud mounting or dual wood studs that are
16” on center.
After installing the display on the mount, the screen can
be locked in place using the convenient locking flag.
A padlock can be used on the latching flag for added
security.
The mount is concealed behind the display, making it a
low profile wall mount.
MSR Series
! IMPORTANT: If the installation of this product requires OSHPD seismic approval, refer to OSHPD pre-approval
documents and drawings before beginning installation. OSHPD documents and drawings are available at
www.chiefmfg.com, and located on the product information page for the mount.
BEFORE YOU BEGIN
x
CAUTION: To prevent damage to your monitor and MSR, which could affect or void the Factory
warranty, thoroughly study all instructions and illustrations before you begin to install the mount. Pay
particular attention to the Warnings and Cautions in this document.
x
The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the
mount must be capable of supporting five times the total weight of the equipment.
x
x
The maximum weight to be installed on the MSR Series static wall mount is 125 lbs (57 kg).
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.
CHIEF MANUFACTURING INC.
8840-000079 RevF
©2007 Chief Manufacturing
10/07
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE. 700
SAVAGE, MINNESOTA 55378 USA
Installation Instructions
MSR Series
PARTS LIST
Prior to assembly, unpack the carton completely. Verify
contents listed in Table 1 and Figure 1.
CONTENTS
DIMENSIONAL DRAWING ..................................... 2
TOOLS REQUIRED FOR INSTALLATION.............. 3
PARTS LIST .............................................................. 3
MSR INSTALLATION .............................................. 4
Select And Prepare Mounting Location.................... 4
Mount the MSR....................................................... 5
ATTACH MSB TO THE DISPLAY ........................... 6
INSTALL THE DISPLAY.......................................... 6
REMOVE THE DISPLAY.......................................... 6
Read installation instructions completely. If you are
missing any of the listed parts, contact Customer Service
at: 1-800/582-6480.
Table 1. Parts List
REF
10
DESCRIPTION
MSR-Series Static Mount
*BOLT, Lag, 5/16” x 2 1/2”
*WASHER, 5/16”
QTY
1
20
2 or 4
2 or 4
1
30
TOOLS REQUIRED FOR
INSTALLATION
**Extender, Latching Flag (not shown)
**Screw, Phillips Machine, 10-24 x 1/2”
(not shown)
1
x
Drill and drill bit set
x
Wrench set
**Nut, Lock, 10-24 (not shown)
1
NOTE: Other tools may be required depending on your
** Included in Latching Flag Extension Kit
method of installation.
* Quantity required is dependent upon mounting
configuration chosen during installation. See “MSR
Installation” section of this document to determine
appropriate quantities.
10
Lag Bolts
20
Washers
30
Figure 1. Parts
3
Installation Instructions
MSR Series
MSR INSTALLATION
Select And Prepare Mounting Location
WARNING: Improper installation can result
in serious personal injury or damage to equipment!
Make sure that the structural members can support a
redundant weight factor five times the total weight of
the equipment. If not, reinforce the structure before
installing the mount. It is the responsibility of the
installer to verify that the framework will safely
support the combined load of the MSR and all
attached components and equipment.
Pilot Holes
Wall
1. Use a stud sensor to locate existing stud(s), and
identify available framework.
2. Identify appropriate mounting hole pattern. See
figures 2 though 4 at right to determine appropriate
mounting hole pattern for the framework identified.
Figure 2. Single Stud Pilot Hole location
Wall
16”
NOTE: The MSR can be mounted using either a two, or
four hole mounting pattern depending upon available
framework. (see Figures 2 through 4)
Pilot Holes
Once suitable framework and appropriate mounting
pattern have been identified:
3. Locate and mark locations of all mounting holes
making certain that marks are on center of all studs.
(see Figures 2 though 4)
Pilot Holes
9 ½”
4. Drill pilot holes using a 7/32” drill bit.
5. Proceed to “Mounting the MSR”.
Wood Studs
Figure 3. Vertical Dual Stud / Masonry Pilot Hole
Location
Wood Studs
Pilot Holes
9 ½”
Figure 4. Horizontal Dual Stud Pilot Hole Location
4
Installation Instructions
MSR Series
6” max. “ Side to Side”
Adjustment
2” max. “Side to Side”
Adjustment
MSR INSTALLATION (Cont’d)
Mount the MSR
To mount the MSR:
1. Place MSR against wall and align MSR upper
mounting holes with upper pilot hole(s) in wall.
(see Figure 5).
2. Install 5/16” x 2-½” lag bolts (20), and 5/16” washers
(30) through MSR upper mounting holes and into
upper pilot holes. DO NOT fully tighten upper lag
bolts at this time.
3. Verify lower MSR mounting hole(s) align with lower
pilot hole(s), and that MSR is properly positioned.
4. Install 5/16” x 2-½” lag bolts (20), and 5/16” washers
(30) through MSR upper mounting holes and into
lower pilot holes.
NOTE: Once mounted on wall, MSR location can be
adjusted up to a maximum of one inch right or
left of slot center, if using slotted mounting holes,
or up to a maximum of three inches right or left if
mounted using the single stud mounting holes
(see Figure 5).
Figure 5. MSR Positioning Adjustments
5. Once MSR is properly positioned, tighten all lag
bolts.
5
Installation Instructions
MSR Series
ATTACH MSB TO THE DISPLAY
To attach the MSB to the display, do the following:
Display
x
To help your identify the correct MSB that matches
the model number of your display, refer to the cross-
x
To download the corresponding MSB installation
OR
x
Contact Customer Service at 952-582-6480 if you
have any questions about how to select the MSB that
matches the model number of your display.
INSTALL THE DISPLAY
IMPORTANT! Display size may impact the ability to
effectively reach the latching flag. If this is the case
install the optional “Latching Flag Extension kit”
provided with mount and reinstall display. See
“Latching Flag Extension Installation” below.
MSR Mount
MSB
To install the display, do the following:
NOTE: Verify that all power/audio/video cables are
disconnected and MSR latching flag is in the
“down” position before attempting to mount
the display.
Figure 6. Install the Display
1. With the aid of another person, lift the display up to
the mount (10) on the wall, aligning mounting
buttons with the teardrop slots on the mount, and
lower the display firmly into place (see Figure 6).
Lock
2. Raise latching flag to secure the display (see Figure
7). If the flag does not fully engage, check to ensure
the mounting buttons are fully seated in the slots.
NOTE: A padlock may be installed through the hole in
Teardrop Slot
the latching flag for additional security.
Unlock
REMOVE THE DISPLAY
Latching Flag
Figure 7. Raise Latching Flag to Lock
To remove the display from the mount, do the following:
1. Disconnect all power/audio/video cables.
2. Lower the latching flag to unlock the display.
3. With the aid of another person, lift the display up and
out of the teardrop slots in the mount to remove the
display.
6
Installation Instructions
MSR Series
Latching Flag Extension
Installation
1. Insert extender slot into top of latching flag.
2. Install screw through latching flag and extender into
nut.
Extender
Locknut
Machine Screw
Latching Flag
Figure 8. Raise Latching Flag to Lock
7
|