Gemini Turntable XL 500 II User Manual

OPERATIONS MANUAL  
Bedienungsanleltung  
Manual de funcionamiento  
Manual de fonctionnement  
Manual del utente  
XL-500 II  
DIRECT-DRIVE MANUAL TURNTABLE  
Handdrehscheibe mit Direktantrieb  
Giradiscos manual de accionamiento directo  
Table tournante manuelle à entraînement direct  
Giradischi manuale a comando diretto  
 
Figure 2  
Figure 3  
Page 2  
 
4. Put the RUBBER MAT (4) on the PLATTER (2).  
Introduction  
Congratulations on purchasing a Gemini XL-500 II turntable. This state of  
the art turntable includes the latest features. Prior to use, we suggest that  
you carefully read all the instructions.  
CARTRIDGE INSTALLATION: (SEE FIG. 2)  
Because all cartridges have their own designs, please refer to your  
particular cartridge’s instructions to insure proper installation.  
Features  
1. Connect the lead wires to the cartridge terminals. For your convenience,  
the terminals of most cartridges are color coded. Connect each lead  
wire to the terminal of the same color.  
±10% Pitch control  
Braking for quick stops  
Strobe illuminator  
White (L+).................................Left Channel +  
Blue (L-)....................................Left Channel -  
Red (R+)................................Right Channel +  
Green (R-).............................Right Channel -  
Soft-touch start/stop switch  
Precautions  
2. Mount the cartridge in the HEADSHELL (5) and tighten it with the  
screws included with the cartridge.  
1. Read all operating instructions before using this equipment.  
2. To reduce the risk of electrical shock, do not open the unit. There  
are NO USER REPLACEABLE PARTS INSIDE. Please contact the  
Gemini Service Department or your authorized dealer to speak to a  
qualified service technician.  
ATTENTION STANTON 680 CARTRIDGE USERS  
When using a Stanton 680 or similar cartridge, where the body  
is grounded to a cartridge terminal, remove the grounding strap  
from the cartridge body to the cartridge ground terminal. Failure  
to do this may result in excessive hum.  
In the U.S.A., if you have any problems with this unit, call  
1-732-969-9000 for customer service. Do not return  
equipment to your dealer.  
HEADSHELL INSTALLATION:  
3. Tone Arm bearings are factory set and sealed. Any attempt at  
adjustment will void the warranty.  
Insert the HEADSHELL (5) into the front of the tubular TONE ARM (6).  
While holding the HEADSHELL (5) firmly in a horizontal position, turn the  
LOCKING NUT (7) counter clockwise until the HEADSHELL (5) is locked in  
place.  
4. Be sure that all AC power is OFF while making connections.  
5. Cables should be low capacitance, shielded and of proper length. Make  
sure that all plugs and jacks are tight and properly connected.  
COUNTERWEIGHT INSTALLATION: (SEE FIG. 3)  
6. Always begin with the audio level faders/volume controls set at  
minimum and the speaker volume control(s) set to OFF. Wait 8 to 10  
seconds prior to turning up the speaker volume to prevent the transient  
“POP” that could result in speaker/crossover damage.  
1. Slide the COUNTERWEIGHT (8) onto the rear of the TONE ARM (6)  
with the numbered stylus gauge facing forward.  
2. Twist the COUNTERWEIGHT (8) lightly counter clockwise, to screw it  
onto the rear of the TONE ARM (6).  
7. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.  
8. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY  
CONTROLS OR SWITCHES.  
ADJUSTING HORIZONTAL ZERO (0) BALANCE AND  
STYLUS PRESSURE:  
1. Without touching the stylus tip, remove the stylus protector (if your  
cartridge has a detachable one).  
Parts Checklist  
Turntable unit.............................................................................1  
Dust cover hinge...........................................................................2  
Turntable platter.............................................................................1  
45 RPM adapter..................................................................................1  
Rubber mat......................................................................................1  
Counter balance..............................................................................1  
Dust cover..........................................................................................1  
Headshell..........................................................................................1  
2. Release the ARM CLAMP (9) and lift the TONE ARM (6) off the ARM  
REST (10).  
3. Counter clockwise advancement of the COUNTERWEIGHT (8) will  
cause the cartridge side of the TONE ARM (6) to be lowered. Clockwise  
will cause the opposite. Turn the COUNTERWEIGHT clockwise or  
counter clockwise as needed until the TONE ARM is balanced horizon-  
tally. You can easily tell this by watching for the point where the TONE  
ARM “floats” freely.  
4. Place TONE ARM (6) on ARM REST (10) and lock it in place with the  
ARM CLAMP (9).  
5. With the TONE ARM (6) locked on the ARM REST (10), hold the  
COUNTERWEIGHT (8) steady with one hand while rotating the  
STYLUS PRESSURE RING (11) until the numeral “0” on the ring aligns  
with the center line on the TONE ARM (6) rear shaft. The horizontal  
zero (0) balance should be completed.  
Assembly and Set-Up  
SEE FIG. 1 ( PAGE 1 ) FOR PART NUMBERS AND LOCATIONS.  
TURNTABLE INSTALLATION:  
6. Refloat the TONE ARM to ensure horizontal zero (0) balance. If zero  
balance has not been maintained, repeat counterweight steps 3 - 5.  
1. Set the TURNTABLE BASE (1) on a flat, level surface free of vibration.  
Try to place the unit as far away from the speakers as possible. Keep  
the unit away from direct exposure to the sun, heat, moisture or dirt.  
Keep the unit well ventilated. Use the turntable feet to horizontally  
stabilize the unit.  
7. After adjusting the horizontal zero (0) balance, turn the balanced  
COUNTERWEIGHT (8) counter clockwise until the cartridge  
manufacturer’s recommend stylus pressure appears on the STYLUS  
PRESSURE RING (11) where it meets the center line of the TONE ARM  
(6) rear shaft.  
2. Make sure that the VOLTAGE SELECTOR (3) switch (located on the  
TURNTABLE BASE) is set to the correct voltage. WARNING: If you try  
to operate the turntable with the incorrect voltage setting, it can damage  
your turntable.  
ADJUSTING THE ANTI-SKATING CONTROL:  
Set the ANTI-SKATING CONTROL (12) to the same value as the stylus  
pressure.  
3. After checking to ensure that all packing materials have been removed,  
gently place the PLATTER (2) on the center spindle of the TURNTABLE  
BASE (1).  
Page 3  
 
INSTALLING THE DUSTCOVER:  
ADJUSTING THE PITCH CONTROL:  
1. Mount the hinges onto the dustcover.  
1. The XL-500 II is equipped with a PITCH CONTROL (21). When the  
PITCH CONTROL is in the center position the speed will be 33 or 45  
depending on which SPEED SELECTOR (15) is pushed.  
2. Hold the dustcover in position, directly above the turntable, and slide the  
hinge bases into the holders mounted on the rear panel.  
2. When the PITCH CONTROL is positioned off center, the pitch can vary  
±10% depending on the position of the PITCH CONTROL.  
3. Always raise the dustcover before removal.  
4. Avoid opening and closing the dustcover during play. Undesirable  
vibration and stylus skipping can result.  
3. The PLATTER (2) is equipped with a STROBE RPM INDICATOR  
STRIP (22) and the POWER (13) switch contains built in STROBE  
LIGHTS (23). When the PLATTER (2) is spinning, the STROBE  
LIGHTS illuminate the STROBE RPM INDICATOR STRIP. At 60 Hz the  
bottom row of dots will appear to be stationary when the speed of the  
platter is exactly 45 RPM and the second row from the bottom will  
appear to be stationary at 33 RPM. At 50 Hz, the second row from the  
top represents 45 RPM and the top row represents 33 RPM.  
CONNECTIONS:  
1. Plug the AC power plug into an appropriate outlet.  
2. See Table A for proper connection of the output RCA plugs and ground  
connector. Make sure that all the plugs are firmly plugged into the  
appropriate jacks (phono inputs). To reduce hum, make sure the ground  
lug is firmly connected to the ground screw.  
PITCH BEND:  
TABLE A  
1. Pushing the PITCH BEND (20) buttons will temporarily raise or lower  
the pitch without changing the slide setting. Releasing the buttons will  
return the pitch to the slide setting.  
MIXER OR RECEIVER  
PHONO L CHANNEL  
PHONO R CHANNEL  
GND Screw  
OUTPUT CONNECTORS  
L (WHITE)  
R (RED)  
GND (Spade Lug)  
Specifications  
TURNTABLE SECTION:  
Operating Instructions  
Type......................................Direct Drive Manual Turntable  
Drive Method................................................................Direct Drive  
Motor.....................................................................Brushless DC Motor  
Platter......................................Aluminum Diecast 13” (332 mm) Dia.  
Speed.............................................................................33 1/3 or 45 RPM  
Starting Torque...................................................................1.2 Kg/cm  
Build-up Characteristics......................0.8 sec. standstill to 33 1/3 RPM  
Braking System....................................................Brake (Solenoid)  
Wow and Flutter...................................................................0.02% WRMS*  
BASIC OPERATION:  
1. Place a record on the RUBBER MAT (4) which sits on the PLATTER (2).  
2. Select the desired speed by depressing the 33 or 45 SPEED  
SELECTOR (15) button.  
3. Turn the POWER (13) switch to the “ON” position, at which point the  
strobe illuminator (built into the POWER (13) switch and the speed  
indicator (for the selected speed) will illuminate.  
4. Remove the stylus protector (if applicable to your cartridge).  
* This rating refers to the turntable assembly and platter only and excludes  
effects of records, cartridges or tonearms.  
5. Release the ARM CLAMP (9) found on the ARM REST (10).  
6. Push the START STOP (14) button. The turntable PLATTER (2) will  
Rumble........................................................................56 dB Unweighted  
start to spin.  
7. Push the CUE LEVER (16) to the “UP” position.  
TONEARM SECTION:  
8. Position the tone arm over the desired position on the record and push  
the CUE LEVER to the “DOWN” position. The TONE ARM (6) will  
slowly lower onto the record at which time play will begin.  
Type...............................................Universal S-Shaped Tubular Arm  
Effective Length.........................................................9 1/16” (230.1 mm)  
Overhang.......................................................................19/32" (15.2 mm)  
Effective Mass......................................................9 g (Without Cartridge)  
Offset Angle......................................................................................22°  
Friction........................................Less Than 7 mg (Lateral, Vertical)  
Tracking Error Angle.....Within 2°32' at the outer groove and within  
0°32' at the inner groove of a 30 cm (12") record  
9. When play is over, raise the TONE ARM (6), move it to the ARM REST  
(10), and secure it with the ARM CLAMP (9).  
10.You now have the option of turning off the power by turning the POWER  
(13) switch to the “OFF” position, or stopping the PLATTER (2) by  
pushing the START STOP (14) button and engaging the electronic  
brake.  
INTERRUPTING PLAY:  
Stylus Pressure Adjust Range..............................................0 - 5 g  
Applicable Cartridge Weight Range...............................................6 - 10 g  
Headshell Weight......................................................................5.6 g  
1. Pushing the CUE LEVER (16) to the “UP” position will cause the TONE  
ARM (6) to lift stopping play.  
2. Pushing the CUE LEVER (16) to the “DOWN” position will cause the  
TONE ARM (6) to slowly lower onto the record at the point where play  
was interrupted.  
GENERAL:  
Power Supply..........................................................115V~60Hz/230V~50Hz  
Power Consumption.....................................................................15 Watts  
Dimensions........................17 3/4” x 6" x 14" (450 x 152 x 352 mm)  
Weight.......................................................................22.5 lbs. (10 Kg)  
PLAYING 45 RPM RECORDS:  
1. When playing a 45 RPM record with a large center hole, first place the  
45 ADAPTER (17) on the center spindle.  
Specifications are subject to change without notice. The weight and  
dimensions shown are approximate.  
2. Be sure that the 45 SPEED SELECTOR (15) button is pushed and the  
45 speed indicator is illuminated.  
TARGET LIGHT:  
1. Push the TARGET LIGHT SWITCH (18) firmly and the TARGET LIGHT  
(19) will illuminate the stylus tip.  
2. When not being used, the TARGET LIGHT should be turned off.  
Page 4  
 
In the U.S.A., if you have any problems with this  
unit, call 1-732-969-9000 for customer service. Do  
not return equipment to your dealer.  
Parts of the design of this product may be protected by worldwide patents.  
Information in this manual is subject to change without notice and does not represent a commitment on the  
part of the vendor. Gemini Sound Products Corp. shall not be liable for any loss or damage whatsoever arising  
from the use of information or any error contained in this manual.  
No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any  
means, electronic, electrical, mechanical, optical, chemical, including photocopying and recording, for any  
purpose without the express written permission of Gemini Sound Products Corp..  
It is recommended that all maintenance and service on the product should be carried out by Gemini Sound  
Products Corp. or it’s authorized agents. Gemini Sound Products Corp. cannot accept any liability whatsoever  
for any loss or damage caused by service, maintenance or repair by unauthorized personnel.  
Worldwide Headquarters • 8 Germak Drive, Carteret, NJ 07008 • USA  
Tel (732) 969-9000 • Fax (732) 969-9090  
France • G.S.L. France • 11, Avenue Leon Harmel, Z.I. Antony, 92160 Antony, France  
Tel: + 33 (0) 1 55 59 04 70 • Fax: + 33 (0) 1 55 59 04 80  
Germany • Gemini Sound Products GmbH • Ottostrasse 6, 85757 Karlsfeld, Germany  
Tel: 08131 - 39171-0 • Fax: 08131 - 39171-9  
UK • Gemini Sound Products • Unit C4 Hazleton Industrial Estate, Waterlooville, UK P08 9JU  
Tel: 087 087 00880 • Fax: 087 087 00990  
Spain • Gemini Sound Products S.A. • Mino, 112, Nave 1, 08223 Terrassa, Barcelona, Spain  
Tel: 011-34-93-736-34-00 • Fax: 011-34-93-736-34-01  
© Gemini Sound Products Corp. 1999  
All Rights Reserved  
 

Elation Professional VCR AR 32CAR 32 User Manual
Electrolux Refrigerator 210621236 11052010 User Manual
Electro Voice Microphone 635A User Manual
Estate Range TEP315VQ User Manual
First Alert Home Security System FA120C User Manual
Fostex DVR D2424LV User Manual
Frymaster Fryer CMIII5 User Manual
Fujitsu Printer FTP 641MCL301 User Manual
Gefen TV Converter Box GTV HDMI 2 HDMIAUD User Manual
Giant Stroller DuPontTM Velpar User Manual