Grizzly Welder T25554 T25555 User Manual

MODEL T25554/T25555  
EXTENSION BLOCK KIT  
INSTRUCTIONS  
For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected]  
Introduction  
Cleanup  
this extension Block Kit increases the maximum  
cutting height of the Model g0555lX/g0555lanv  
14" bandsaw from 6" to 12".  
the unpainted surfaces of the extension block are  
coated with a heavy-duty rust preventative that  
prevents corrosion during shipment and storage.  
the t25554 matches the black color scheme of  
the g0555lanv. the t25555 matches the green  
color scheme of the g0555lX.  
Complete removal of the rust preventative is nec-  
essary for the extension block and upper arm to fit  
properly and be accurately positioned.  
Before cleaning, gather the following:  
disposable rags  
a
Cleaner/degreaser (Wd•40 works well)  
safety glasses & disposable gloves  
plastic paint scraper (optional)  
C
d
e
B
Basic steps for removing rust preventative:  
1. put on safety glasses.  
F
figure 1. t25555 extension Block Kit.  
2. apply a liberal amount of cleaner/degreaser  
on the rust preventative, then let it soak for  
5–10 minutes.  
Inventory  
Description  
Qty  
a. extension Block.......................................... 1  
B. saw Blade 105".......................................... 1  
C. extended saw Blade guard....................... 1  
D. extended guide post ................................. 1  
E. hardware  
—hex Bolt 5/8"-11 x 8-1/2 ......................... 1  
—hex nut 5/8"-11....................................... 1  
—5/8" Flat Washer..................................... 2  
—Cord Clamp aCC-3 (not shown)............. 1  
—phillips hd scr 10-24 x 12" (not shown) . . 1  
f. extended Blade guard assembly.............. 1  
3. Wipe off the surfaces. if your cleaner/  
degreaser is effective, the rust preventative  
will wipe off easily. if you have a plastic paint  
scraper, scrape off as much as you can first,  
then wipe off the rest with the rag.  
4. repeat Steps 2–3 as necessary until clean,  
then coat all unpainted surfaces with a quality  
metal protectant to prevent rust.  
NOTICE  
Items Needed  
Qty  
avoid chlorine-based solvents, such as  
acetone or brake parts cleaner, that may  
damage painted surfaces.  
adjustable Wrenches ....................................... 2  
phillips screwdriver #2...................................... 1  
hex Wrench 5mm and 3mm ....................1 each  
another person for assistance.......................... 1  
Copyright © May, 2012 By grizzly industrial, inC. revised april, 2013 (tr)  
WaRNINg: NO pORTION Of ThIS MaNUaL May BE REpRODUCED IN aNy ShapE  
OR fORM WIThOUT ThE WRITTEN appROvaL Of gRIzzLy INDUSTRIaL, INC.  
(For Models ManuFaCtured sinCe 4/13) #Kn15002 printed in taiWan  
 
10. remove the guide post control knob and lock  
collar (figure 4) from the pinion gear shaft.  
17. replace the lock collar and guide post control  
knob.  
11. push the pinion gear shaft inward to disen-  
gage the gear from the rack (see figure 5).  
18. attach the guide assembly and the extended  
blade guard to the guide post.  
1
19. attach the cord clamp using (1) 10-24 x 2  
"
pinion gear  
disengaged  
phillips head screw (see figure 7), and  
replace the power switch assembly and dou-  
ble cord clamp removed in Step 4.  
Ball plunger  
set screws  
Front view  
rear view  
figure 5. pinion gear shaft pushed in.  
12. unthread the two ball plunger set screws  
(figure 5) away from the guide post. (it is not  
necessary to remove them.)  
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
13. hold the guide post with one hand, then  
loosen the lock knob with the other hand and  
slide guide post up and out of its housing.  
14. insert the extended guide post into the hous-  
ing, as shown in figure 6, making sure the  
keyway is aligned with the set screw.  
figure 7. extension block installed.  
Keyway  
20. install the 105" bandsaw blade, and without  
starting the saw, tension the blade approxi-  
mately where it should be for a regular cutting  
operation.  
set screw  
—if you have difficulty setting the tension on  
the 105" blade, the tensioning mechanism  
on the bandsaw may need to be re-adjust-  
ed to accommodate the new blade length.  
Follow the Blade Tensioner instructions in  
the g0555lX owner's Manual.  
figure 6. installing extended guide post.  
15. slide the pinion gear away from the saw and  
ensure the gear teeth engage the guide post  
rack.  
21. align the bandsaw wheels so they are  
coplaner. refer to Wheel alignment proce-  
dure in the g0555lX owner's Manual.  
16. thread the ball plunger set screws back into  
place—but avoid over-tightening them. at the  
proper setting, the guide post should move  
up and down by hand, but remain stationary  
when the lock knob is released.  
Congratulations! the riser block installation  
procedure is now complete.  
-3-  
T25554/T25555 Extension Block Kit  
 
Riser Block parts Breakdown  
7
9
11  
1
2
12  
13  
4
6
8
5
10  
15  
14  
2
3
T25554 parts List  
T25555 parts List  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
1
PB120  
PW14  
PN04  
HEX BOLT 5/8-11 X 8-1/2  
FLAT WASHER 5/8  
HEX NUT 5/8-11  
1
PB120  
PW14  
PN04  
HEX BOLT 5/8-11 X 8-1/2  
FLAT WASHER 5/8  
HEX NUT 5/8-11  
2
2
3
3
4
PT25555004 SOLID PIN 6 X 15  
4
PT25555004 SOLID PIN 6 X 15  
5
PT25555005 SAW BLADE 6 TPI X 105 X 3/8  
PT25555006 LEFT-SIDE BLADE GUARD  
PT25555007 EXTENDED GUIDE POST  
PT25554008 EXTENDED BLADE GUARD (ORANGE)  
PT25554009 BLADE GUARD (ORANGE)  
PT25554010 EXTENSION BLOCK (BLACK)  
5
PT25555005 SAW BLADE 6 TPI X 105 X 3/8  
PT25555006 LEFT-SIDE BLADE GUARD  
PT25555007 EXTENDED GUIDE POST  
PT25555008 EXTENDED BLADE GUARD (RED)  
PT25555009 BLADE GUARD (RED)  
6
6
7
7
8
8
9
9
10  
11  
12  
13  
14  
15  
10  
11  
12  
13  
14  
15  
PT25555010 EXTENSION BLOCK (GREEN)  
PCB02  
PW07  
CARRIAGE BOLT 5/16-18 X 1/2  
FLAT WASHER 5/16  
PCB02  
PW07  
CARRIAGE BOLT 5/16-18 X 1/2  
FLAT WASHER 5/16  
PWN03  
WING NUT 5/16-18  
PWN03  
WING NUT 5/16-18  
PT25555014 CORD CLAMP ACC-3  
PS01 PHLP HD SCR 10-24 X 1/2  
PT25555014 CORD CLAMP ACC-3  
PS01 PHLP HD SCR 10-24 X 1/2  
Parts breakdown provided for reference only. Not all parts shown are available for purchase.  
-4-  
T25554/T25555 Extension Block Kit  
 

Graco Dollhouse 311511G User Manual
Grizzly Drill G0643 User Manual
GSI Outdoors Clothes Dryer PNEG 1447 User Manual
Harbor Freight Tools Air Compressor 40131 User Manual
Harbor Freight Tools Biscuit Joiner 96067 User Manual
Hasselblad Camera Lens CB 48 160 User Manual
HP Hewlett Packard Personal Computer B2B96UT#ABA User Manual
Hunter Fan Thermostat 40170 User Manual
iHome MP3 Docking Station iDL45 User Manual
Image Treadmill IMTL391052 User Manual