HP Hewlett Packard Mouse 26 753 User Manual

Step Two  
Charging the Batteries  
Step Four  
Connecting the Charger  
to the Computer  
1. Connect the  
1. Plug the supplied USB receiver into the  
USB socket on the back of the charger.  
supplied AC  
adapter to the DC  
jack on the back of  
thesuppliedcharger.  
USB 27 MHz  
Wireless Optical Mouse  
26-753  
2. Plug the charger’s USB connector into a  
USB port on your computer.  
Then, plugtheother  
end of the adapter  
into a standard  
AC outlet.  
Owner’s Manual  
for installing, setting up and using your new product  
2. Place the mouse’s  
charging contacts on the charger’s contacts to  
charge the batteries.  
Thank you for buying an HP USB 27 MHz Wireless  
Optical Mouse. The mouse’s advanced RF (radio  
frequency) technology enables 360-degree operation  
around your computer - no line-of-sight placement  
required. Its ergonomic design lets you hold and use  
it comfortably. The mouse’s optical technology  
senses mouse movements precisely and smoothly,  
with no moving parts to clean or replace.  
The green charging indicator lights. Charge the  
rechargeable batteries at least 8 hours before  
you use the mouse for the first time.  
Caution: You must use a regulated Class II power  
source that supplies 5V DC and delivers at least  
450 mA. Its center tip must be set to positive and its  
plug must fit the charger’s DC jack. The supplied  
AC adapter meets these specifications. Using an  
adapter that does not meet these specifications  
could damage the charger or the adapter.  
Notes:  
USB Receiver  
Step Five  
Synchronizing the Mouse  
Step One  
1. Plug the supplied USB receiver into the  
USB port for the supplied charger, your  
computer, or keyboard.  
Installing the Batteries  
1. Open the battery compartment cover  
by squeezing the mouse’s sides  
where it attaches to the mouse as  
shown.  
2. Place the mouse within 1 foot of the  
USB receiver.  
System Requirements  
Hardware — IBM PC or compatible with one  
available USB port and a CD drive.  
The mouse wheel flashes blue when the  
battery is low.  
You can also use AA alkaline batteries in the  
mouse if the rechargeable batteries are weak.  
If you do this, be sure not to place the mouse in  
the charger.  
You must reset the channel when you replace  
the rechargeable batteries. See “Setting the  
Channel” for more information.  
3. Use a pointed object such as a pen to  
press Connect on the bottom of the  
mouse for less than 1 second.  
2. While squeezing the sides of the  
mouse, pull the battery  
Software — Microsoft Windows 98, Windows  
98SE, Windows 2000, Windows ME, or  
Windows XP.  
4. Press Synchronization on the USB receiver. The blue LED on the USB  
receiver flashes, showing that the mouse and USB receiver are  
synchronized.  
compartment cover out with your  
other hand.  
Windows NT does not support the USB interface.  
Note: If the mouse and USB receiver do not synchronize, remove the batteries  
from the mouse and unplug the USB receiver. Then wait about 20 seconds. Next,  
reinstall the batteries in the mouse and repeat the steps in this section.  
Installing Software  
As Windows 98/98 SE does not support the  
mouse’s scroll function, you must install the  
supplied software to use the mouse. Follow these  
steps ONLY if you have Windows 98/98 SE.  
5. Move the mouse around. The cursor on your computer screen should move,  
showing that the mouse is ready to use. The blue LED on the USB receiver  
lights when you use the mouse.  
Connect  
Step Three  
Setting the Channel  
Your mouse uses two  
RF channels and up to  
256 ID codes. Channel  
and ID are  
automatically selected  
when you connect the  
mouse to the receiver.  
Step Six  
Using the Charger With the USB Receiver  
1. Make sure the supplied USB receiver is  
connected to the computer.  
3. Insert the two supplied Ni-MH  
batteries into the battery  
compartment as indicated by the  
polarity markings (+ and -)  
marked inside.  
The supplied charger with USB port and cable and  
USB receiver make it easy to connect the mouse to a  
notebook computer for traveling or a desktop computer  
at home. When traveling, you can detach the USB receiver  
from the charger and then attach it to your notebook com-  
puter. When at home, you can attach the USB receiver to  
the charger and then connect the charger’s USB cable to  
the computer.  
2. Insert the supplied mouse driver CD into your  
computer’s CD ROM drive.  
3. Follow the on-screen instructions to finish  
installing the mouse driver.  
When you change the  
batteries in your  
mouse or receive  
interference from  
4. Replace the battery compartment  
cover.  
What’s Included  
another wireless mouse,  
you must set the RF channel.  
To set the channel, use a pointed object to press  
Connect on the bottom of the mouse.  
Note: If you attach the supplied mini USB receiver to your notebook computer,  
always carry the charger separately so you can charge the mouse whenever  
necessary.  
Mouse  
USB Receiver  
Charger  
AC Adapter  
Owner’s Manual  
Driver CD  
AA Ni-MH Rechargeable Batteries (2)  
 

Graco Baby Playpen PD123415A User Manual
Harman Kardon Stereo Receiver AVR 8500 User Manual
Hasbro Games 04 110 User Manual
Hasselblad Camera Lens CFi 45 38 User Manual
Heart Home Collectables Indoor Fireplace MHC36 User Manual
Heatiator Indoor Fireplace BH42A User Manual
Hoshizaki Ice Maker KMD 900MAH User Manual
HTC Cell Phone PB00100 User Manual
Hunter Fan Outdoor Ceiling Fan 99122 User Manual
Impex Home Gym DBR 92 User Manual