Hearth and Home Technologies Indoor Fireplace 36EBU User Manual

7205240100REV00  
Installation Guide for the  
36-EBU and 42-EBU Electric Fireplace  
LISTINGS AND CODE APPROVALS  
The EBU series fireplaces have been tested in accordance with the UL 2021 and CSA C22.2 No. 46 standards for fixed  
and location-dedicated electric room heaters.  
MODEL SPECIFICATIONS  
Model  
Number  
Rated Power  
Watts  
Remote  
Control  
Wall  
Thermostat  
Mesh  
Screen  
AMPS  
120Volt  
AMPS  
208Volt  
AMPS  
240Volt  
Description  
Voltage Volts  
36-EBU  
42-EBU  
36” Standard  
42” Standard  
120/208/240  
120/208/240  
1650/2340/3025  
1650/2340/3025  
Included  
Included  
Included  
Included  
Included  
Included  
13.75  
13.75  
11.25  
11.25  
12.6  
12.6  
NOTE: Power ratings shown include the light bulbs and motor (275 watts)  
STEP-BY-STEP INSTALLATION (Note: Please read all instructions before installing)  
1. Rough in framing opening following the recommended dimensions (Section A: Framing).  
2. Allow 8” of service cable for connecting to the junction box on the fireplace. Remove the outer jacket and strip  
the individual conductors ½” from the end.  
3. Loosen the screw securing junction box cover and remove the cover.  
4. Remove knockouts if necessary or use the provided cable clamp.  
5. Place unit in position in the opening, level with shims if necessary and attach unit to frame using nailing flanges  
provided.  
6. Unit is factory wired for 208/240 volt power supply. If 120 volt operation is required, slide the switch and  
reconfigure the wiring as covered in section C wiring. Wires L1, L2, N & G are attached to the rear of the  
junction box cable clamp for easy access.  
7. Wire a dedicated, properly fused circuit with a 20amp rating for the appropriate voltage (120, 208/240).  
8. Make wall mounted thermostat connections as outlined in Section C: Wiring.  
9. Place all connectors inside the unit and replace the junction box cover, ensuring that the cable clamp grips only  
the jacket of service or thermostat.  
266-950 5/03  
 
SECTION C: WIRING  
NOTE: The unit is factory configured for 208/240 volt operation  
NOTE: All wiring must be completed prior to installing the unit.  
NOTE: Ensure that the power conversion switch is in the proper position for the required supply voltage prior to  
connecting the unit to power supply.  
240 VOLT INSTALLATIONS  
1. Locate the switch on the top corner of the unit.  
2. Ensure that the switch is in the 230 volt position.  
3. Loosen the screw securing the junction box cover and remove the cover.  
4. Remove the knockouts (if necessary) or use the provided cable clamp.  
5. Pull out the four wires marked L1, L2, N, and G.  
6. Connect the black L1 wire from the unit to the L1 from the power supply. Connect the red L2 wire from the unit  
to the L2 from the power supply. Connect the white N wire from the unit to the neutral from the power supply.  
Connect the green ground wire from the unit to the ground from the power supply.  
7. When the unit has been configured for the appropriate power supply voltage, ensure that all connections are  
tight. Insert all the wiring into the unit and secure with a cable clamp.  
TO RECONFIGURE FROM 240 VOLT TO 120 VOLT  
1. Locate the switch on the top corner of the unit.  
2. Flip the switch from 230 volt to 115 volt configuration.  
3. Loosen the screw securing the junction box cover and remove the cover.  
4. Remove the knockouts (if necessary) or use the provided cable clamp.  
5. Pull out the four wires marked L1, L2, N, and G.  
6. Connect the black L1 wire from the unit to the L1 from the power supply. Connect the red L2 and white N wires  
to the neutral from the power supply. Connect the green ground wire from the unit to the ground from the power  
supply.  
7. When the unit has been configured for the appropriate power supply voltage, ensure that all connections are  
tight. Insert all the wiring into the unit and secure with a cable clamp.  
TOP OF FIREPLACE  
230 VOLT/115 VOLT SWITCH  
 
WALL MOUNTED THERMOSTAT WIRING  
NOTE: Wiring of the thermostat must be completed prior to installing the unit.  
NOTE: The following installation instructions are for a single pole thermostat included with the unit.  
120 / 240VOLT INSTALLATIONS  
The wall mounted thermostat is connected to the fireplace by running a 2 conductor wire with a ground from the junction  
box on the back of the unit to the thermostat.  
1. Locate the switch on the top corner of the unit and ensure that the power conversion switch is in the proper  
position for the required supply voltage.  
2. Loosen the screw securing the junction box and remove the cover. Pull out the wire nut that contains wires  
marked 1 & 2.  
3. Remove the wire nut and separate the wires marked 1 & 2.  
4. Connect one of the wires from the thermostat to the wire marked 1 and the other wire to the wire marked 2.  
5. Connect the ground wire from the thermostat to the ground wire grouping from the power supply.  
6. Ensure that all connections are tight. Insert all the wiring into the unit and secure with a cable clamp.  
 
WIRING DIAGRAM WITH REMOTE CONTROL  
 
Service Parts  
36-EBU, 42-EBU  
(NG, LP) Exploded Part Diagram  
(GN, PL) Vue éclatée des pièces  
Beginning Manufacturing Date: 6-01  
Ending Manufacturing Date: ______  
12  
11  
9
2
5
6
1
3
4
8
7
10  
 
36-EBU, 42-EBU Electric Fireplace Service Parts List  
36-EBU  
None  
42-EBU  
None  
MODEL >  
MOD. LEVEL >  
ITEM  
REPLACEMENT PART  
PART NUMBER  
1
1
2
3
4
5
6
7
8
9
LOG SET  
0438200300RP  
0438440100RP  
5900160100RP  
2800070400RP  
2800070500RP  
8800240103RP  
2500130100RP  
6900360100RP  
6900190500RP  
5300110300RP  
3000200300RP  
2200460100RP  
2300200200RP  
2300200100RP  
TS901W  
0438200300RP  
0438440100RP  
5900160200RP  
2800070400RP  
2800070500RP  
8800240203RP  
2500130100RP  
6900360100RP  
6900190500RP  
5300110300RP  
3000200300RP  
2200460100RP  
2300200200RP  
2300200100RP  
TS901W  
30" LOG SET  
MIRROR ASSEMBLY  
POWER ON/OFF SWITCH  
AUXILARY CONTROL SWITCH  
MESH CURTAIN  
LOWER LIGHT HARNESS  
AC MOTOR  
REFLECTOR ROTISSERIE  
BLOWER ASSEMBLY  
10 REMOTE CONTROL ASSEMBLY  
11 ELEMENT  
12 TEMPERATURE LIMITING SWITCH  
HIGH LIMIT CUTOUT  
WALL MOUNTED THERMOSTAT  
REMOTE CONTROL TRANSMITTER  
CIRCUIT BOARD  
3000200600RP  
3000200700RP  
0438290100RP  
8800250100RP  
2500180100RP  
3000200600RP  
3000200700RP  
0438290100RP  
8800250200RP  
2500180100RP  
MIRROR CHANNEL  
MESH SCREEN ROD  
VOLTAGE SELECTOR SWITCH WITH WIRES  
Use Sylvania light bulbs item #SL13460 that can be ordered via the website www.lite-house.com or by call 1-800-838-  
0977. You can also buy replacement bulbs at most hardware stores and home centers: clear chandelier Candelabra  
bulbs with E-12 (small) socket base, 60 watts rating. Ex. GE 60BC or Phillips 60CTC.  
 

HannsG Computer Monitor HG171AB User Manual
Healthrider Treadmill 831299301 User Manual
Honeywell Air Cleaner 203365A User Manual
Hotpoint Cooktop GW74 User Manual
HP Hewlett Packard Camcorder V5040u User Manual
HP Hewlett Packard Network Card IA 2 User Manual
HTC Cell Phone OXYG100 User Manual
Hunter Fan Ventilation Hood 20090201 User Manual
Husqvarna Snow Blower 14527SB LS User Manual
Impex Home Gym MWM 900 User Manual