Honeywell Home Security System HCD544 User Manual

HCD544/HCD544X/HCD545X Camera  
Quick Install Guide  
Document 800-03503 — Rev C — 03/09  
Adjusting the Back Focus  
To adjust the back focus, aim the camera towards a darker area, or use a Neutral  
Density lens filter. For best results, there should be a minimum of 15 ft (4.5 m)  
between the camera and the target focal area.  
Important Safety Instructions  
1. Loosen the setscrews (see Figure 1) with a Phillips screwdriver.  
2. Set the Zoom lens adjustment to Wide and the Focus lens adjustment to Near.  
3. Adjust the back focus ring to focus the picture.  
Read and keep these instructions.  
Heed all warnings.  
Follow all instructions.  
Do not use this apparatus near water.  
Clean only with dry cloth.  
Do not block any ventilation openings. Install in accordance with the manufacturer’s  
instructions.  
4. Retighten the setscrews.  
Mounting the Camera  
Do not install near any heat sources such as radiators, heat registers, stoves, or other  
apparatus (including amplifiers) that produce heat.  
Use only with the bracket or mounting system specified by the manufacturer, or sold  
with the apparatus.  
There are mounting points on the top and bottom of the camera (see Figure 3) to  
mount the camera on a bracket or tripod. Use standard sized mounting bolts to install  
the camera to a mounting bracket.  
Refer all servicing to qualified service personnel.  
Caution Follow local installation codes for proper mounting bracket support  
capability.  
Figure 3  
Camera Mounting.  
Installation  
Top view shown  
The HCD544 Series camera is designed for general surveillance applications and is  
ideally suited for low-light indoor environments.  
Mounting point  
Installing the Lens  
The HCD544 Series camera is factory configured for a CS-mount lens. Screw the lens  
(customer supplied) into the front of the camera body. An IR corrected Day/Night lens  
is recommended for this camera.  
Making Final Adjustments  
Adjust the focus in your field of view until you see a clear image. If necessary, adjust  
the brightness using the OSD menu controls (see LENS DC/BRIGHTNESS or AGC).  
Confirm the exposure on the monitor screen.  
Figure 1  
Lens Installation  
Programming  
DC Lens Pin Definitions  
OSD Menu Controls  
Setscrews (x2)  
Pin Function  
1
2
3
4
CTRL -  
CTRL +  
DRV +  
DRV -  
Figure 4  
Camera Controller  
3
1
4
2
Navigating through the menus  
Camera OSD control  
(4 position plus  
center press (ENTER)  
Press this control To do this …  
ENTER  
Press and hold two seconds to enter  
SETUP menu. Press to enter a  
screen or select a menu option.  
Connecting the Camera  
Note Check the power source from the external power supply before applying  
power to the camera.  
UP, DOWN  
(!, ")  
Move vertically between menus and  
options. Increase/decrease a value.  
1. Connect the VIDEO connector on the rear of the camera to the video-in connector  
on your monitor or video recorder.  
LEFT, RIGHT  
(#, $)  
Move horizontally between menus  
and options.  
2. HCD544/HCD544X models: Connect the camera to a power supply appropriate  
for your installation (12 VDC or 24 VAC).  
..  
Indicates submenus. Select the  
menu, then press ENTER.  
Plug the power supply into an appropriate power source.  
3. HCD545X model: Connect the power cord to the power cord socket.  
RETURN (on OSD Exit the submenu. Select RETURN,  
submenus) then press ENTER.  
Plug the power cord plug into an electrical outlet of AC230V, 50 Hz. Accepted  
voltage range is 207 VAC~253 VAC.  
Note Menu display turns off automatically after five minutes of  
no activity. Your changes will be saved.  
The power LED illuminates to show that the camera is receiving power.  
Figure 2  
Video Connections  
OSD Menu Structure  
HCD544/HCD544X  
Power LED  
The HCD544 Series camera menu system consists of one main SETUP menu for easy  
camera programming.  
Figure 5  
Menu Structure  
Submenu  
Main Menu  
Menu Options  
LAMP terminal  
GND terminal  
DC .., MANUAL  
LENS  
AC24V/DC12V terminal block  
HCD545X  
Power LED  
230 VAC  
SHUTTER  
WHITE BAL  
BACKLIGHT  
AGC  
FLK, MANUAL .., ESC  
power supply  
<<SETUP MENU>>  
DC  
ATW .., AWC (PUSH/LOCK), AWC  
AUTO ..,USER .., MANUAL ..  
1
2
3
4
5
6
7
LENS  
SHUTTER  
WHITE BAL.  
BACKLIGHT  
AGC  
MANUAL ..  
AWC ..  
ON  
GND terminal  
LAMP terminal  
30dB  
ON, OFF  
SPECIAL ..  
EXIT MENU ..  
Connecting LAMP Contact  
18 dB~30 dB, OFF  
See SPECIAL Menu.  
The HCD544 camera is equipped with LAMP and GND external contact terminals (see  
Figure 2). When the LAMP terminal is connected to the GND terminal, the camera is  
forced into night mode (see DAY&NIGHT). It stays in night mode until the LAMP  
terminal is disconnected from the GND terminal.  
for a description of the  
submenus and menu options.  
SPECIAL ..  
Document 800-03503 – Rev C – 03/09  
 
     

GPX Portable Speaker SA119B User Manual
Graco Outboard Motor ti18496b User Manual
Greenheck Fan Server 455049 User Manual
Greenheck Fan Ventilation Hood WD 400 Series User Manual
Grizzly Saw G0665 User Manual
Haier Dishwasher DW12 EFET User Manual
Hasbro Robotics 83557 User Manual
Honeywell Home Security System 128BPTSIA User Manual
Huffy Board Games Table Top Basketball Game User Manual
Hunter Fan Ventilation Hood 82001 User Manual