Hunter Fan Outdoor Ceiling Fan 28331 User Manual

INSTALLATION INSTRUCTIONS FOR HUNTER  
CEILING FAN LIGHT KITS MODELS:  
28330, 28331, 28332, 28333, 28334, 28335, 28336, 28337, 28338, 28339, 28340, 28341, 28342  
28343, 28344, 28345, 28405, 28406, 28407, 28408, 28982, 28983, 28984, 28985, 28986, 28987  
Light Kit Lead Wires  
and Wire Connectors  
CAUTIONS  
Read entire text carefully before beginning in-  
stallation and save these instructions.  
Bellmouth Nut  
To reduce the risk of electrical shock, install  
this light kit only on Hunter ceiling fan  
models with removable switch housings.  
Fan Speed  
Switch  
W ARNING  
To avoid possible electrical shock, before in-  
Capacitor  
Capacitor  
stalling light fixtur es, disconnect power by  
turning of f the cir cuit breakers both to the  
Multi-wire Plug  
Connection  
outlet box and to its associated wall switch  
M3 Housing  
Assembly Screws  
location. If you cannot lock the cir cuit break-  
ers in the of f position, secur ely fasten a  
prominent war ning device, such as a tag, to  
the service panel.  
Reverse Switch  
FIGURE 1  
4. Locate and car efully remove the two capacitors  
from the switch housing.  
Connect house wiring to the fan befor e at-  
taching the light fixtur e to the fan.  
All wiring must be in accor dance with na-  
tional and local electrical codes and ANSI/  
NFPA 70. If you ar e unfamiliar with wiring,  
you should use a qualified electrician.  
5. You have now disconnected the wiring har ness  
and its components fr om the switch housing and  
are ready to install them into the modular acces-  
sory light kit.  
STEP 2: INSTALLING WIRING HARNESS  
NOTE: Refer to Figure 1 for steps listed below.  
STEP 1: REMOVING WIRING HARNESS  
Before you can install the modular accessory light  
kit, you must remove the wiring har ness and its com-  
ponents from the modular switch housing on the  
fans listed above. You must then install the wiring  
harness into the modular accessory light kit.  
1. Locate the two wir es in the lower switch housing  
labeled “Connect Light Here” or “For Light Use”.  
One will be white, the other black with a white stripe.  
Unscew the wire connectors counterclockwise  
to expose the bare metal leads.  
NOTE: Refer to Figure 1 for the steps listed below.  
2. Locate the white wire and the black wire coming  
from the light fixture.  
1. Locate the reversing switch and car efully remove  
the two screws holding the reversing switch to  
the switch housing. The r eversing switch can now  
be removed from the switch housing.  
Connect the black wir e from the light fixture to  
the black wire with a white stripe from the  
lower switch housing.  
2. Remove the patented br eakaway connector from  
the fan pull chain.  
Connect the white wire from the light fixture to  
the white wir e from the lower switch housing.  
3. Carefully loosen the bellmouth nut from the fan  
pull chain and remove the fan pull chain switch  
from the switch housing.  
To fasten the wir es, twist the two bare leads to-  
gether. Place a wire connector over the intertwined  
length of wire and twist clockwise until tight.  
41490-01 03/12/2009  
 

Graco Washer Dryer 3A1332A User Manual
Graham Field Medical Alarms GF13605 User Manual
Haier Refrigerator HW24WF10NG User Manual
Harbor Freight Tools Grinder 30304 User Manual
Havis Shields Automobile Accessories Interior Dome Light User Manual
Heat Controller Air Conditioner SMA 18 User Manual
Hotpoint Washer WMFG 631 User Manual
HP Hewlett Packard Digital Camera E217 User Manual
HP Hewlett Packard Photo Printer A430 User Manual
Ice O Matic Beverage Dispenser CD20030 CD20530 User Manual