Iluv Headphones i202 User Manual

Ear Clip Headset with Bluetooth® Wireless Technology  
Instruction Manual  
i202  
Please read this manual carefully before operating and save it for future reference.  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
USER SAFETY GUIDE  
FCC Notice (USA)  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following  
two conditions: (1) this device may not cause harmful interference, and (2) this device  
must accept any interference received, including interference that may cause undesired  
operation. Refer to 47 CFR Sec. 15.19.  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio  
communications, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
NOTE: Changes or modifications not expressly approved by the party responsible  
for compliance could void the user’s authority to operate the equipment. Refer to  
47 CFR Sec. 15.21.  
Industry Canada Notice to Canadian Users  
Operation is subject to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference received, including  
interference that may cause undesired operation of the device. Refer to IC RSS 210 Sec.  
5.11. The term “IC” before the certification or registration number only means that the  
registration was performed based on a Declaration of Conformity and that Industry  
Canada technical specifications were met. It does not imply that Industry Canada (IC)  
approved this equipment. Refer to Self-Marking 6(f) and RSP 100 Sec. 4.  
About Electromagnetic Interference (EMI)  
This device is designed and manufactured not to exceed the exposure limit for radio  
frequency energy, which is set by the Federal Communications Commission of the U.S  
government.  
The term “EMI” is short for the electromagnetic interference caused by the  
electromagnetic field generated by electronic devices. In fact, most electrical appliances  
and devices emit electric and magnetic fields, and most of modern electronic devices are  
susceptible to the EMI if they are inadequately shielded or designed.  
- 2 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
USER SAFETY GUIDE  
About Electromagnetic Interference (EMI) - Continued  
If you use any personal medical device, such as a pacemaker, please consult the  
manufacture of your medical device to determine if it is adequately shielded from EMI.  
Your physician might assist you in obtaining this information.  
Please turn off this device if you are instructed to do so, especially on an airplane or  
in a hospital.  
Please keep away from medical instruments in a hospital or medical unit while using  
this device.  
IMPORTANT NOTES ON HEARING  
Your hearing is very important to you and to us. We strongly recommend you to follow  
the guideline below in order to prevent possible damage to or loss of hearing.  
Hearing experts caution that listening to loud sounds can damage hearing over time. With  
continuous listening to loud sounds, hearing adapts and will give the impression that  
volume has reduced. What seems normal may, in fact, be harmful. To guard against this  
before hearing adapts, set the volume at a low level and slowly increase the volume level  
until sound can be heard comfortably and clearly without distortion. Damage to hearing is  
cumulative and irreversible. Ringing or discomfort in the ears indicates that the volume is  
too loud. Once a comfortable listening level has been established, do not increase the  
volume level further.  
Cautions  
If you experience a ringing sound in your ear, lower the volume or discontinue the use  
of this product.  
Do not use the headphones while driving or cycling. Because this product reduces  
the external noises, you might not be able to hear the warning sounds, such as an  
automobile horn, and might result in a traffic accident. Additionally, listening to  
headphones while driving is illegal in many places  
- 3 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
TABLE OF CONTENTS  
GETTING STARTED  
Introduction. …..………..…………………………………………………………..……  
What’s Included ……………………………………..…………………………………… 5  
What is Bluetooth wireless technology? ................................................................  
5
6
Charging the headset and audio adapter……………………………………………… 7  
Using your Computer’s USB port to charge…………………………………………… 7  
Notes on charging…………………………………………….…………………………  
7
OPERATING INSTRUCTIONS  
Location of controls……………………………………………………………………… 8  
Turning on/off the i202 or wireless audio adapter……………………………………  
8
Pairing i202 with your mobile phone or audio device………………………………… 9  
Notes on pairing………………………………………………………………………… 10  
Pairing i202 with the included wireless audio transmitter (dongle)………………… 11  
How to wear the i202 ear clip headphones………………..………………………… 12  
Listening to music…………………………………………………………………………12  
How to control music playback………………………………………………………… 13  
Making a call……………………………………………………………………………… 14  
Mute a call………………………….……….…………………………………………… 14  
Answering a call………………………….……….……………………………………… 15  
Notes on answering a call……………….……………………..…………..…………… 15  
Ending a call……………….………………………………………………………………15  
Rejecting a call………………………………………………………………………….. 15  
TROUBLESHOOTING GUIDE  
Questions and answers about the product…………………………………………… 16  
SPECIFICATIONS  
Technical information about the product……………………………………………… 18  
- 4 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
GETTING STARTED  
iLuvTM Stereo Ear Clips with Bluetooth® Wireless Technology  
Experience the freedom of Bluetooth wireless technology with i202 stereo ear clip  
headphones. Not only can you listen to music from an audio device featuring Bluetooth  
wireless technology, but you won’t miss a call while you’re at it. Music is important to  
people, but so is that urgent (or friendly) phone call. With the i202, it’s the best of both  
worlds. What’s even better is the inclusion of an audio adapter (dongle) with Bluetooth  
wireless technology. The dongle lets you convert almost any audio device into a wireless  
device even if it’s nailed to the floor or hanging on the wall. Now your music playback  
options seem endless and yet with a simple press of a button, an incoming call can be  
answered or an outgoing call can be made. What could be more convenient? Well, try on  
the comfortable ear clips which fit comfortably around the ear as if they were a natural  
extension of them. Talk for as long as 13 hours if you want to. Listen as long as 14 hours.  
It’s really up to you. Enjoy the wireless freedom the i202 provides.  
Get caught up in the music instead of the wires  
Listen to your music wirelessly with Bluetooth wireless technology  
Answer or make your calls wirelessly without taking your mobile phone out  
Audio devices without Bluetooth wireless technology can connect to i202 using the  
included wireless audio transmitter  
The swivel and ear-clip design secures the perfect comfortable fit on your ear  
Integrated remote control functions (Play / Pause / Skip / Stop)*  
Supports HSP, HFP, A2DP, and AVRCP profiles  
Standby time up to 200 hours  
Continuous listening time up to 14 hours  
Continuous talking time up to 14 hours  
Communication range up to 33ft  
Compliant with Bluetooth V1.2  
What’s Included  
Wireless stereo ear-clip headset  
Wireless audio transmitter  
USB power adapter  
USB cable  
Instruction manual  
Warranty card  
- 5 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
GETTING STARTED  
What is Bluetooth wireless technology?  
Bluetooth wireless technology is a short-range wireless  
communication technology intended to replace the cables  
connecting electronic devices while maintaining the high  
level of security. With Bluetooth wireless technology, two  
devices can communicate at the same time without the  
need to face each other or the concern of interference  
from other wireless communication within its optimum  
range of 33 feet.  
Through a process called “Pairing,” two or more devices  
with Bluetooth wireless technology can interact with each  
other without interference from other wireless platforms  
nearby, including other Bluetooth wireless  
communications between unrelated devices.  
Note: In order to use this headset with other devices featuring Bluetooth wireless  
technology, such devices must be supported by the same profiles as the headset. Refer  
to the owner’s manual of the accompanying device for its Bluetooth profiles and for  
pairing instructions and operating features.  
* The integrated remote control feature is only supported when the connected devices  
support the remote control feature through Bluetooth wireless technology.  
When connected to a computer or a USB power adapter with the included USB cable,  
i202 can only be charged. Its other functions will be disabled. Also depend on the Audio  
devices software, remote control function might be limited.  
- 6 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
GETTING STARTED  
Charging the Headset and Audio Adapter  
Before the first use of this headset, it is recommended to fully charge the headset and the  
included audio adapter (dongle). To do so, follow the instructions below:  
1. Open the mini USB port dust cover (on the  
bottom of the right ear clip, or top right on the  
dongle) before attaching USB cable.  
2. Attach other end of cable to supplied USB  
power adapter.  
3. Plug the supplied USB power adapter to an AC outlet.  
4. Plug the other end to the USB connector on the headset or  
dongle. The red light will be on when connected. When  
the headset/dongle is fully charged, the red light will go off.  
5. Unplug the USB adapter when the headset/dongle is fully charged.  
Using your Computer’s USB port to Charge  
If your computer has a USB port, you can also charge the headset or dongle using your  
computers USB port.  
1. Follow the directions above for connecting the USB cable to the headset or dongle.  
2. Connect the USB cable into the USB plug on a computer.  
3. Unplug when fully charged.  
Notes on Charging  
Use only the included power adapter to charge the headset.  
The built-in rechargeable battery should be charged at least once every two months.  
Headset cannot be used while charging.  
Important: If your unit displays red flash and you hear long beep sound while operating,  
this indicates low battery condition, so please charge the unit before operating again.  
- 7 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
OPERATING INSTRUCTIONS  
Location of Controls  
Turning On/Off the i202 or Wireless Audio Adapter  
To turn on the i202 and/or the included wireless audio adapter (dongle), press and hold  
the Multi-function button on the headset or the On/Off button on the dongle for  
approximately three (3) seconds. A blue light will blink near the Multi-function button on  
the headset and on the On/Off button on the dongle. Additionally, the i202 headset will  
make a high-pitched beep. The blue blinking light (and beep from the headset) indicates  
that the device has been turned on.  
To turn off the i202 or wireless audio adapter, press and hold the Multi-function button  
and the On/Off button on the dongle. When the blinking red light flashes four (4) times it  
has been turned off  
- 8 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
OPERATING INSTRUCTIONS  
Pairing i202 with your Mobile Phone or Audio Device  
Before using this headset, make sure that it is paired with a mobile phone and audio  
devices with Bluetooth wireless technology. To pair with such a device, follow the  
instructions below:  
1. Please make sure the headset is turned off.  
To Turn i202 if it is currently turned on then  
press the Multi-Function button for  
approximately five (5) seconds. There will be  
a high-pitched beep with red light flashes  
about 4 times and headset will be off.  
2. Press and hold the Multi-function button  
for approximately five (5) seconds until the  
red and blue lights blink alternately  
around the button. The headset is now  
ready for pairing. (Note: Pressing the  
Multi-function button longer than five (5)  
seconds will turn off the headset. If this  
fails, then turn off the headset and turn it  
on again by holding the Multi-Function button for five (5) seconds for pairing mode)  
3. Set your mobile phone or audio  
device to its pairing mode  
(phones and audio devices with  
Bluetooth wireless technology will  
have their own pairing  
instructions. See owner’s manual  
of the phone or device for these  
instructions).  
4. Place the mobile phone or audio device and the i202 close  
together during pairing. The mobile phone and most audio  
devices will detect i202 and identify it, displaying the model  
number i202.  
5. Once the i202 has been identified, confirm as per the  
instructions on the device. You will be required to enter a  
password on the next screen.  
- 9 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
OPERATING INSTRUCTIONS  
Pairing i202 – Continued  
6. Enter the password: “0000.” The phone or device will  
display a confirmation message after a few seconds. Once  
the headset is correctly paired, the light will stop blinking  
red and blue alternately, and will blink blue only.  
7. Repeat this procedure each time an additional phone or  
audio device needs to be paired with the i202.  
8. Enjoy music and  
answer calls  
wirelessly using the  
i202.  
Notes on Pairing  
Be aware that in order to answer and place calls while listening to music, the i202  
must be paired with a mobile phone BEFORE it is paired with audio devices or the  
audio adapter.  
This headset will not be recognized by your mobile phone unless it is properly paired.  
The i202 cannot pair with mobile phones which are not designed with Bluetooth  
wireless technology. It is important to follow both these instructions and those which  
accompany the corresponding mobile phone or audio device.  
The i202 can also be paired with a computer which supports Bluetooth wireless  
technology. For pairing instructions for such a computer, consult the owner’s manual  
for the computer or see a computer specialist.  
The i202 is designed to remember pairing information even when it is turned off.  
However, this feature only works if the corresponding mobile phone is designed with  
the same feature. Consult the owner’s manual of the mobile phone or audio device  
for these design features.  
The i202 can only be paired with two devices at the same time; one with the mobile  
phone and the other with an audio device or the supplied wireless audio transmitter.  
Attempting to pair the i202 with a third device will result in the loss of the previous  
pairing connection.  
- 10 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
OPERATING INSTRUCTIONS  
Pairing i202 with the Included Wireless Audio Transmitter (Dongle)  
The i202 can be used with an audio device that is not designed to support Bluetooth  
wireless technology using the supplied wireless audio transmitter (dongle). In order to  
answer and place phone calls while using the dongle, it is important to pair the mobile  
phone first. After pairing the mobile phone according to the previously-listed instructions,  
follow these directions to set the pair the i202 with the dongle.  
1. Set the i202 into pairing mode following instructions 1 and 2 on the previous page.  
2. Press and hold the On/Off button on the dongle for  
approximately five (5) seconds.  
3. Blue and red alternating lights will blink around the  
On/Off button indicating that the dongle is now in pairing  
mode.  
4. Place the headset near the dongle when both are in pairing mode.  
5. When the alternating red  
and blue blinking lights on  
both devices change to a  
blue blinking light ONLY,  
pairing is complete.  
6. Plug the 3.5mm end of the dongle into the  
headphone jack of an audio device and enjoy  
music playback wirelessly through the i202  
stereo headphones.  
Note: Only the volume can be controlled on the  
i202 when using the dongle. All other functions  
(skip, stop, forward, etc.) must be controlled using  
the controls on the audio device itself.  
- 11 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
OPERATING INSTRUCTIONS  
How to Wear the i202 Ear Clip Headphones  
The i202 stereo ear clip headphones are designed for a comfortable fit on the ears. The  
ear clip with the Multi-function button and controls should be worn on the right ear, while  
the other ear clip is worn on the left.  
1. Holding the ear clip in one hand, use one finger to push  
the ear rest out to extend it.  
2. Place the ear clip over  
your ear and release  
the ear rest.  
3. Each ear clip headphone should fit tightly, comfortably and securely on your ears  
Listening to Music  
Once you have paired the i202 with either an audio device which supports Bluetooth  
wireless technology or with the included wireless audio transmitter (dongle), you can  
enjoy listening to music wirelessly.  
For a direct connection with an audio device that supports Bluetooth wireless  
technology.  
a. Pair the i202 with the audio device as instructed in the section, “Pairing i202 with  
your Mobile Phone or Audio Device” if you have not done so already.  
b. Switch both the i202 and the audio device ON. (Note: The i202 is designed to  
maintain pairing settings even when one or both devices are switched off.  
However, this feature only functions when the paired audio device is designed  
with the same feature. If the paired audio device does not support this function, it  
may need to be paired again once it has been switched off and switched back on.  
Please refer to the owner’s manual for the audio device to determine if it has this  
feature.)  
c. Start playing music using the controls on the device to listen to music on the i202.  
(Note: If the device supports the protocol which allows playback functions to be  
controlled from the headset, you can operate these functions directly through the  
i202. If not, only the volume can be controlled through the headset.)  
- 12 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
OPERATING INSTRUCTIONS  
Listening to Music - Continued  
For connection to an audio device without Bluetooth wireless technology using the  
included wireless audio adapter (dongle).  
a. Pair the i202 with the dongle as instructed in the section, “Pairing the i202 with  
the Included Wireless Audio Transmitter (Dongle)” if you have not done so  
already.  
b. Switch the i202, the dongle and the audio device ON. (Note: The i202 will  
maintain pairing information with the dongle even when either or both devices are  
switched off. It is not necessary to pair them again.)  
c. Start (and continue) playing music wirelessly with the controls on the audio device  
itself. (Note: When using the dongle, the i202 will only control the volume. All  
other functions must be controlled by the device’s controls)  
How to Control Music Playback  
The i202 supports the remote control feature. In other words, the Play (Resume), Pause,  
Skip Forward, Skip Backward, Stop functions can all be controlled through the headset if  
the audio device to which it is paired also supports this feature. Please refer to the  
owner’s manual for the audio device with Bluetooth wireless technology for information  
on this function. If the audio device does not support this feature, music playback must be  
controlled using the controls on the device itself. If the audio device supports the remote  
control feature, playback functions can be controlled through the headset. (Note: The  
i202 can not initiate playback for any audio device. Music playback must be always  
started using the audio device’s controls. Once playback is started, the i202 can control  
certain functions of a compatible device. Also note that depends on the audio devices,  
you might have limited remote control due to software issues.)  
Play (Resume) / Pause: To pause during playback, press  
the Three-way (__ / / ``) button on the i202. To resume  
playback in the pause mode, press the Three-way (__ /  
`` ) button again.  
/
Stop: To Stop press and hold Play/ Pause button for three  
(3) Seconds.  
Skip forward / Skip backward:  
To skip to the next song, slide  
the Three-way (__ / / ``)  
button on the headset to (``). To  
skip to the previous song, press  
the Three-way (__ /  
/ ``)  
button to the (__) position.  
- 13 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
OPERATING INSTRUCTIONS  
How to Control Music Playback - Continued  
Volume Up / Down: To increase the volume,  
press the Volume (+) button. To decrease  
the volume, press the Volume (-) button.  
Making a Call  
The i202 is designed to allow a user to place and answer calls while listening to music  
wirelessly with Bluetooth wireless technology. Your mobile phone must be paired with the  
i202 FIRST before pairing with other audio devices or the wireless audio transmitter. How  
calls are made, however, depends greatly on the phone to which the i202 is paired.  
1. Voice dialing: This unit supports voice dialing only if the corresponding mobile phone  
supports voice dialing. Please consult the owner’s manual of your mobile phone to  
see if this feature is available. It is recommended that this headset is used to record  
the dialing voice.  
a. Press the Multi-function button once.  
b. Say the name of the person you want to call.  
Some newer phones will ask you to confirm from among a choice of similar  
sounding names from which you respond with “yes,” or “no.”  
Other older phones will dial directly from your voice recording of a particular  
name.  
Please refer to the owner’s manual for your mobile phone for instructions  
regarding this function.  
2. Normal dialing: Dial the telephone number on your mobile phone. When the call  
connects, it will be heard through the headset.  
3. Adjusting the volume: Press the Volume buttons (+/-) to a comfortable listening  
level. This function only works when supported by the corresponding mobile phone.  
Mute a Call  
The i202 has mute capability when using i202 with  
Cell-phones with Bluetooth technology.  
To mute during your phone call, press pause button  
to enable mute and press it one more time to release.  
- 14 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
OPERATING INSTRUCTIONS  
Answering a Call  
It is very simple to answer a call with the i202, whether listening to music or already  
talking on the phone.  
1. An incoming phone call will be indicated by a ring after which the blue light on the  
i202 will blink. Press the Multi-function button once to answer the call.  
2. If the call is received while you are listening to music, the music will pause or mute  
(depending on your audio device’s formatting), and the call can be taken.  
3. If the headset is off when there is an incoming call, press the Multi-function button to  
turn on the headset and answer the call as usual.  
4. If your mobile phone supports the “automatic function” and it is turned on, this  
headset will automatically answer the phone whenever there is an incoming call.  
5. Please refer to the operating instructions in the owner’s manual of your mobile phone  
and your audio device regarding these functions.  
Notes on Answering a Call  
When there is an incoming call, some phones might not ring when paired with i202,  
but there will be a beeping sound from the headset. Press the Multi-function button  
to answer the phone when you hear this beep.  
Similarly, some phones may not send an incoming call signal to the headset. Press  
the Multi-function button when the phone rings.  
Ending a Call  
There are several ways to end a phone call.  
1. Short Press the Multi-function button on the headset.  
2. Press the End key on the mobile phone.  
3. The call will end automatically when the person on the other end hangs up.  
4. If you were listening to music when the call came in, you will return to music playback  
once the call is ended.  
Rejecting a Call  
To reject an incoming call, long press the Multi-function button for approximately three  
(3) seconds. The incoming call will be cut off. (Note: Do not press the Multi-function  
button longer than three (3) seconds as the headset will shut down.)  
Note: Your mobile phone with Bluetooth wireless technology must be paired with the i202  
BEFORE these functions are attempted. If audio devices or audio adapter are paired  
before the mobile phone, these functions will not perform. Also note that not all cell-  
phones with Bluetooth technologies are compatible with each other please see owner’s  
manual that came with the device for more details.  
- 15 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
TROUBLESHOOTING GUIDE  
1. The headset does not work with my mobile phone.  
o
Be certain that your mobile phone is equipped with Bluetooth wireless  
technology. This headset will only work with such mobile phones.  
Additionally, your mobile phone must be paired with the headset BEFORE  
all other pairing.  
2. There is interference on the headset with my phone or music playing  
devices.  
o
The maximum distance for Bluetooth wireless technology is 33 feet (10  
meters). When this distance is approached, background noise will  
increase. Also, a poor signal on the mobile phone may contribute to  
degradation the quality of sound as well.  
3. There is no sound.  
Ensure that the mobile phone or music player is turned on and set up  
correctly. Be certain that the volume is turned up on both devices.  
o
4. Sudden drop of volume or hear static or distortion when using Devices  
with Bluetooth technology  
o
o
o
Please check your battery level and charge if necessary.  
Make sure you are not too far away from the unit.  
Make sure you are free from any interfering devices such as walls and  
any other wireless devices.  
5. Pairing with other devices with Bluetooth technology is not working.  
o
Be sure to check your devices manual to see if A2DP Bluetooth Profile is  
supported.  
o
o
o
Make sure the devices are not too far away from each other.  
Make sure to put the correct password (The default password is “0000”).  
Check with your devices manual if the device supports other Bluetooth  
products.  
- 16 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
TROUBLESHOOTING GUIDE  
o
Make sure both devices are in pairing mode to accept connections from  
each other.  
o
Make sure the Bluetooth device you are using is Bluetooth Version 1.2 or  
higher for stable connectivity.(Some of the V1.1 devices might not be fully  
compatible. Make sure to check your Bluetooth devices manual for  
compatibility issues)  
6. Can not pair with stereo headset with Bluetooth technology made by  
other manufacturers.  
o
This could happen if the device has its own security method, or unique  
password other then “0000”. Please check with the manufacturer for  
compatibility issues. For full compatibility we recommend iLuv Bluetooth  
Stereo Headset.  
o
o
Make sure headset supports A2DP Bluetooth Stereo Profile.  
Make sure the device is fully charged and you are not too far away from  
the unit.  
o
Make sure you are not using mono headset to pair. (This will not work  
since mono headset uses different Bluetooth profile. If profiles do not  
match with the devices you are connecting to, pairing will fail. Please  
check your device manual, or check with manufacturer to see if device  
has matching A2DP Bluetooth Stereo Profile)  
7. Remote functions like play/pause skip/fwd skip/bkwd does not work  
o
Depends on the device these function might be disabled due to software  
issues.  
o
o
Please refer to owner’s manual of the device you are using.  
If you are using Audio Dongle, most of these dongle will not support  
remote functions, so it is normal for device when control is not working  
- 17 -  
 
Ear Clip Headset w/ Bluetooth wireless technology  
V10M10_IM_EN_11082006  
SPECIFICATIONS  
Speaker Driver: 30mm NdFeB speaker driver  
Frequency Response: 20Hz – 20kHz (receiving)  
SPL: 118dBA  
Bluetooth Version: V1.2  
Bluetooth Profile: HSP, HFP, A2DP, AVRCP  
Standby Mode: < 200hrs  
Listening Mode: < 14hrs (@ max. volume)  
Talking Mode: < 14hrs (@ max. volume)  
Power Sources  
o
Built-in rechargeable battery  
ƒ
ƒ
ƒ
Battery Type: Lithium Polymer  
Battery Capacity: 380mAh  
Charging Time: 2.5 Hours  
o
o
USB power adapterꢀ  
ƒ
ƒ
Input: AC 100V – 240V, 50Hz/60Hz  
Output: DC 5V / 0.5A  
USB port on a computerꢀ  
Power Input: 5V / 500mA  
Unit Dimension (W x H x D): Approx. 55mm x 58.5mm x 21mm (2.2” x 2.3” x 0.8”)  
Unit Weight: Approx. 51g (0.11 lbs)  
Wireless Audio Transmitter  
Bluetooth Version: V1.2  
Bluetooth Profile: A2DP, AVRCP  
Continuous Working Time: 5.5 hours  
Power Sources  
o
Built-in rechargeable battery  
ƒ
ƒ
ƒ
Battery Type: Lithium Polymer  
Battery Capacity: 160mAh (nominal)  
Charging Time: About 2 Hours  
o
o
USB power adapterꢀ  
ƒ
ƒ
Input: AC 100V – 240V, 50Hz/60Hz  
Output: DC 5V / 0.5A  
USB port on a computerꢀ  
Power Input: 5V / 500mA  
Power Consumption: Audio Input 500mV  
Cord: 2.36” / PVC  
Plug: 3.5mm / Gold-plated / Stereo  
Unit Dimension (W x H x D): Approx. 25.0mm x 6.0mm x 60.0mm (0.98” x 0.24” x  
2.36“)  
Unit Weight: Approx. 14g (0.03 lbs)  
* Specifications and features are subject to change without notice.  
- 18 -  
 
TEL: 516-626-7188  
FAX: 516-626-7105  
iLuv is a trademark of jWIN Electronics Corp. Features and specifications are subject to change without prior  
notification. iPod is a trademark of Apple Computer, Inc. The Bluetooth word mark and logos are owned by Bluetooth  
SIG, Inc and any use of such marks by jWIN Electronics Corp. is under license. Mobile phone and iPod not included in  
this package.  
© 2006 jWIN Electronics Corp. All rights reserved. No portion of this printed material or product enclosed herewith  
including design, shape and graphics, may be reproduced or transmitted in any form without the expressed written  
consent of jWIN Electronics Corp. by any means, electronic or mechanical, including photocopying, recording or the  
use of an information storage and retrieval system. Any unauthorized distribution or reproduction of this printed material  
or product, or any portion thereof, will be prosecuted to the fullest possible extent of the law.  
Printed in China  
 

Graham Field Pill Reminder Device 5717 1 EA User Manual
HANNspree Flat Panel Television DT04 12A1 User Manual
Hans Grohe Plumbing Product 06571XX0 User Manual
Harbor Freight Tools Portable Generator 68120 User Manual
Harbor Freight Tools Staple Gun 93197 User Manual
Harman Kardon CD Player HD710 User Manual
HP Hewlett Packard Digital Camera 618 User Manual
Hubbell Switch Series 2015 User Manual
Hudson Sales Engineering Indoor Furnishings HUWF1534 User Manual
Hunter Fan Outdoor Ceiling Fan 28331 User Manual